NOTE: Avoid damaging the cord while fixing the base to the wall or when removing or replacing the product from the base.
RECHARGING (FIG. C)
From new, the rechargeable cells of the product need a minimum charge time of 16 hours to ensure full power. While charging the charge indicator light will be illuminated. The switch must be in the off (O) position. The product will not charge if it is in any other position. While charging, the product may get warm, this is perfectly normal and safe. It can remain on charge indefinitely without damage or danger.
It is not possible to overcharge the battery cells with the charger provided. workmanship. The defective product will be replaced or repaired at no charge in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailers policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized
Service Center for repair or replacement at our option. Proof of purchase may be required. Black &
Decker owned and authorized Service Centers are listed under Tools-Electric in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state. Should you have any questions, contact the manager of your nearest Black & Decker Service Center.
This product is not intended for commercial use.
701 E. Joppa Rd.
Yellow Pages for Service & Sales
THIS PRODUCT IS FOR DRY PICK-UP ONLY.
SWITCH (FIG. D)
Always return the product to the charging base immediately after use so that it will be ready and fully charged for the next use. Ensure that the product is fully engaged on the charging base.
CLEANING THE PRODUCT (FIGS . E-I)
WARNING: Never use the Dustbuster without its filters.
NOTE: The filters are re-usable, do not confuse them with disposable dust bags, and do not throw
them away when the product is emptied. We recommend that you replace the filters every
6-9 months depending on frequency of use. (Use Cat. No. VF100 filters)
FIG. E Remove the dust bowl by pressing the dust bowl release button and pulling the bowl down and out. To replace the bowl, place it back onto the handle and click firmly into position.
Important: For best vacuum results, empty bowl after every use.
FIG. F Empty the debris from the bowl and wash if necessary (see Fig. H).
FIG. G To remove the filters twist the outer (plastic) filter in a clockwise direction. Shake or lightly brush any loose dust off the outer filter. Remove the inner filter and shake, tap or lightly brush outside surface to remove loose dust. Both filters can be rinsed as shown in fig. (H).
WARNING: Filter must be dry before re-assembling.
Ensure both filters are in place before operating.
FIG. G1 If your unit is equipped with a filter cleaning wheel as shown in Fig. G1 you can achieve more use between filter cleanings by first switching off the vac, and then rotating the cleaning wheel up or down as shown. Make two full rotations of wheel for best results.
FIG. H Wash the filters using warm, soapy water and ensure that they are completely dry before using it again. The cleaner the filters are, the better the product will perform. It is very important that the filter is correctly in position before use. The dust bowl can also be washed in warm soapy water. Ensure that it is dry before re-attaching.
WARNING: Filters must be dry before re-assembling.
N de catalogue CHV7200, CHV9600, CHV9610, CHV9650,
CHV1200, CHV1400, CHV1410, CHV1450, CHV1560
M ERCI D AVOIR CHOISI B LACK & D ECKER !
POUR ENREGISTRER VOTRE NOUVEAU PRODUIT.
AVANT DE RETOURNER CE PRODUIT POUR QUELQUE
RAISON QUE CE SOIT, COMPOSER LE
AVANT DAPPELER, AYEZ EN MAIN LE N DE CATALOGUE ET LE CODE DE DATE. DANS LA PLUPART
DES CAS, UN REPRSENTANT DE BLACK & DECKER PEUT RSOUDRE LE PROBLME PAR
IMPORTANT: Maximum dust collection will only be obtained with clean filters and an empty dust bowl.
If dust begins to fall back out of the product after it is switched off, this indicates that the bowl is full and requires emptying.
FIG. I The exhaust filter is removed by opening cover and pulling out filter as shown. For best results wash filter regularly with soap and water.
FIG. J Never immerse the product in water. A damp cloth and soapy water should be used to clean the exterior of the motor section. Always ensure the product is completely dry before re-use or storing.
Your product is very economical to charge. While it is charging it uses less electricity than a typical night light bulb.
When fully charged and with a clean filter, the average effective usage times vary by voltage.
7.2 volts: 7 - 9 minutes
9.6-12 volts: 9-11 minutes
14.0 volts and higher: 12-15 minutes
If the product does not work, check the following:
That the charge indicator light is on when unit is in base.
The charger was correctly plugged in for recharge. ( It feels slightly warm to the touch.)
The charger cord is not damaged and is correctly attached to the base.
The charger is plugged into a working electrical outlet.
That the switch is in the OFF position when charging.
Accessories are stored on the product (FIG. K) and are fitted into the nose of the product for use.
Accessory use is shown in FIG. L.
Note: Replacement filters can be purchased from most local/national retailers that sell vacuums. Look for VF100 filters.
BATTERY REMOVAL AND DISPOSAL
This product uses nickel-cadmium (Ni-Cd) rechargeable and recyclable batteries. When the batteries no longer hold a charge, they should be removed from the Vac and recycled. They must not be incinerated or composted.
The batteries can be taken for disposal to a Black & Decker, Company-Owned or Authorized Service
Center. Some local retailers are also participating in a national recycling program
(see RBRCTM Seal). Call your local retailer for details. If you bring the batteries to a Black & Decker
Company-Owned or Authorized Service Center, the Center will arrange to recycle old batteries. Or, contact your local municipality for proper disposal instructions in your city/town.
To remove the battery pack for disposal:
1. Remove accessories from the bottom of the unit.
2. Using a Phillips screwdriver remove the screws as shown in Fig "M". Then use the screwdriver to push the lock tabs in the direction shown.
3. Pull the battery cover off as shown in Fig. N.
4. Using a Phillips screwdriver remove the two battery location screws as shown in Fig "O". After removing the screws push the battery pack back as shown.
5. Remove the battery pack (Fig. P) and dispose as stated above.
To replace or obtain a new battery pack, contact your local Black & Decker, Company-Owned or
Authorized Service Center, or call 1-800-54-HOW-TO (544-6986). Be prepared to provide the