Frigidaire 10,000 BTU Window-Mounted Slider / Casement Air Conditioner user guide

Features three different fan speeds, for more cooling flexibility.Maximum comfort throughout the evening hours with the added benefit of energy savings. With Sleep Mode, the temperature gradually increases a few degrees over the evening.Customize times to fit your schedule for immediate comfort when you get home. The built in timer allows you to preset the unit to turn on and off in half hour increments.
ELECTRONIC CONTROL

Before you begin, thoroughly familiarize yourself with the control panel and remote as shown below and all its functions, then follow the symbol for the functions you desire. The unit can be controlled by the touch pad alone or with the remote.

TEMPERATURE/TIME

EXHAUST SELECTOR

CHECK FILTER

RESET BUTTON

TEMPERATURE

TURNS UNIT

SLEEP MODE

Battery Size: AAA

Warning: Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable

(nickel-cadmium) batteries.

STANDARD REMOTE

Operating Instructions

The following instructions represent the Touch Pad, the same instructions can be used for the Remote Control.

TO TURN UNIT ON:

PRESS ON/OFF

2009 Electrolux Home Products, Inc.

YOU WILL SEE:

Note: The unit will run in energy saver mode when used for the first time. In this mode, the fan will continue to run for 1 minute after the compressor shuts off. The fan then cycles on for 20 seconds at 10 minute intervals until the room temperature is above the set temperature, at which time the compressor turns

All rights reserved.

Operating Instructions

Operating Instructions

(continued)

TO CHANGE TEMPERATURE SETTlNG:

TO ADJUST FAN SPEEDS:

YOU WILL SEE:

Note: Tap or hold either up (

) or down (

) button until the desired temperature is seen on the display. This temperature will be automatically maintained anywhere between

60 F (16 C) and 90 F (32 C) . If you want the display to read the actual room temperature. See "To Operate on Fan

Only" section on Page 7.

YOU WILL SEE:

PRESS TO SELECT

TO USE AUTO FAN FEATURE:

YOU WILL SEE:

PRESS FAN BUTTON

CHOOSE AUTO

Note: Fan starts at High Speed and adjusts to a slower speeds the room temperature dictates. For example, if the room doesn't get too warm, it will stay at the slowest speed. If the room temperature rises quickly, such as a door being opened, it will automatically go to the highest speed. The fan speeds will re-adjust back to the slowest speed as the room returns to the original set temperature. Press either the fan slower or fan faster button to adjust the fan speed manually.

2009 Electrolux Home Products, Inc.

All rights reserved.

Operating Instructions

Operating Instructions

(continued)

TO OPERATE ON FAN ONLY:

YOU WILL SEE:

MODE BUTTON

Note: Use this function only when cooling is not desired, such as for room air circulation or to exhaust stale air on some models. (Remember to open the vent during this function, but keep it closed during cooling for maximum cooling efficiency.) You can choose any fan speed you prefer. (Except Auto Fan).

During this function, the display will show the actual room temperature, not the set temperature as in the cooling

YOU WILL SEE:

COOL FEATURE:

Note: In this mode, the fan remains on all the time with the compressor cycling on and off when room temperature is

MODE BUTTON

CHOOSE COOL

SLEEP FEATURE:

YOU WILL SEE:

SLEEP BUTTON

2009 Electrolux Home Products, Inc.

Note: In this mode the selected temperature will increase by 2 F 30 minutes after the mode is selected. The temperature will then increase by another 2 F after an additional

30 minutes. This new temperature will be maintained for 7 hours before it returns to the originally selected temperature. This ends the "Sleep" mode and the unit will continue to operate as originally programmed. The "Sleep" mode program can be cancelled at any time during operation by again pressing the "Sleep" button.

All rights reserved.

Operating Instructions

Operating Instructions

(continued)

TIMER: DELAY STOP / START FEATURE

TIMER BUTTON

SET BUTTONS

YOU WILL SEE HOW MUCH TIME IS CHOSEN:

Note: For Delay Stop, the unit must be in the On position?

Note: For Delay Start, the unit must be in the Off position.

First, Press TIMER button, then adjust timer setting, tap or hold the UP arrow (

) or the DOWN arrow ( change delay timer at 0.5 hour increments, up to 10 hours, then at 1 hour increments up to 24 hours. The control will count down the time remaining until start (8, 7.5, 7, etc.).

The Delay Start Operation automatically selects cooling with maximum Fan speed (if Cool, Energy Saver, or Fan Only was the last mode selected) . The t