Frigidaire 12,000 BTU Built-In Room Air Conditioner with Supplemental Heat- 230V/60Hz user guide

Reduce your utility bills while still keeping your home cool; this unit turns on and off at different intervals to ensure that the room stays at the set temperature.Customize times to fit your schedule for immediate comfort when you get home and preset the unit to turn on and off in half hour increments.Enjoy more cooling flexibility with three different fan speeds.
ELECTRONIC CONTROL

Before you begin, thoroughly familiarize yourself with the control panel and remote as shown below and all its functions, then follow the symbol for the functions you desire. The unit can be controlled by the touch pad alone or with the remote.

TURNS UNIT

REMOTE TEMP

CHECK FILTER

RESET BUTTON SENSING INDICATOR

(some models)

TEMPERATURE/TIME

TEMPERATURE

Light Feature:

The display and all LED indicators on the control panel of the unit can be turned off by pressing the "Light" button on the remote control. If any other button of the control panel and remote control is pressed after that, the unit will beep to indicate it works as the corresponding direction of pressing specific button, and the display and LED indicators will illuminate accordingly, but they will turn off again in 5 seconds if no further operation.

Press the "Light" button again or unplug the unit to cancel this setting.

STANDARD REMOTE

WITH DISPLAY & REMOTE

SENSING BUTTON

Battery Size: AAA

Warning: Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.

Operating Instructions

The following instructions represent the Touch Pad, the same instructions can be used for the Remote Control.

TO TURN UNIT ON:

PRESS ON/OFF BUTTON

2009 Electrolux Home Products, Inc.

YOU WILL SEE:

NOTE: The unit will run in Cool mode with Eco feature and Auto fan speed setting when used for the first time.

With the Eco feature, when the room temperature is below the set temperature, the fan will continue to run for 3 minutes after the compressor shuts off. The fan then cycles on for 2 minutes at 10 minute intervals until the room temperature is above the set temperature, at which time the compressor turns back on.

Eco feature can be activated or deactivated by pressing Eco button, but it is invalid in fan only mode.

All rights reserved.

Operating Instructions

Operating Instructions

(continued)

AUTO FEATURE:

YOU WILL SEE:

Note: This mode is a fixed combination of Cool mode and

Auto fan speed setting. In this mode, the fan speed can not be selected manually.

MODE BUTTON

CHOOSE AUTO

COOL FEATURE:

YOU WILL SEE:

MODE BUTTON

CHOOSE COOL

TO CHANGE TEMPERATURE SETTlNG:

2009 Electrolux Home Products, Inc.

Note: In this mode, the fan remains on all the time with the compressor cycling on and off when room temperature is

YOU WILL SEE:

Note: Tap or hold either up (

) or down (

) button until the desired temperature is seen on the display. This temperature will be automatically maintained anywhere between

62 F (17 C) and 86 F (30 C). If you want the display to read the actual room temperature. See "To Operate on Fan

Only" section on Page 8.

All rights reserved.

Operating Instructions

Operating Instructions

(continued)

TO ADJUST FAN SPEEDS:

YOU WILL SEE:

Note: The fan speed can be selected among four settings:

Auto, Lo(Low), Med(Medium) and Hi(High), unless the unit runs in "Auto" or "Dry" mode, or the Sleep feature is activated.

PRESS TO SELECT

TO USE AUTO FAN FEATURE:

YOU WILL SEE:

PRESS FAN BUTTON,

CHOOSE AUTO

TO OPERATE ON FAN ONLY:

MODE BUTTON

2009 Electrolux Home Products, Inc.

Note: Fan starts at Low Speed and adjusts to a proper speed according to the room temperature dictates. For example, if the room doesn't get too warm, it will stay at the slowest speed. If the room temperature rises quickly, such as a door being opened, it will automatically go to the highest speed.

The fan speeds will re-adjust back to the slowest speed as the room returns to the original set temperature.

YOU WILL SEE:

Note: Use this function only when cooling is not desired, such as for room air circulation or to exhaust stale air on some models. (Remember to open the vent during this function, but keep it closed during cooling for maximum cooling efficiency.) You can choose any fan speed you

During this function, the display will show the actual room temperature, not the set temperature as in the cooling

All rights reserved.

Operating Instructions

Operating Instructions

(continued)

YOU WILL SEE:

MODE BUTTON

CHOOSE DRY

SLEEP FEATURE:

YOU WILL SEE:

SLEEP BUTTON

CHECK FILTER FEATURE:

Note: This feature is a reminder to clean the Air Filter (See

Care and Cle