Frigidaire 24'' Built-in Dishwasher with EvenDry™ user guide

Unlike traditional spray arms, our BladeSpray® arm rotates in two directions, so you get better water coverage that reaches every corner.Save time loading and unloading and fit more with a third level rack that easily fits silverware, cooking utensils and tools.With the fan assisted EvenDry™, air flow is evenly circulated and moisture is removed for clean, spot-free dishes every time.
Your dishwasher uses a DishSenseTM Technology to understand how much food is on the dishes and then adjusts the cycle accordingly.

Property Damage Hazard

Before starting dishwasher be sure that the water is connected and turned on. Failure to do so may cause damage to the pump seal and result in water leakage.

Wash Cycle Selections

Cycle times are approximate and will vary with options selected. Hot water is necessary to activate dishwasher detergent and melt fatty food soils. An automatic sensor will check the incoming water temperature and, if it is not hot enough, the cycle will be lengthened for automatic water heating in the main wash and final rinse of all cycles. This happens even when HI-TEMP WASH option has not be selected. When HI-TEMP WASH is selected, an even higher temperature will be reached to handle heavier soil loads.

The programmed cycles default to the normal temperature option, to choose HI-TEMP or

SANITIZE press WASH TEMP pad again.

Hi-Temp Wash Option

HI-TEMP WASH option is selected, by pressing the WASH TEMP pad. The dishwasher heats water in the main wash to approximately 140F

(60C) and increases the temperature higher in the final rinse to help with the drying stage.

This helps dishwasher detergent remove food grease and soil from dishes more effectively and aids in drying performance by adding additional rinse aid and increasing the water temperature.

Sanitize Option

To sanitize your dishes and glassware, select

SANITIZE option, by pressing WASH TEMP pad.

When selected, the light will come on and remain on until end of cycle. The water temperature in the final rinse will be raised to 155F (68C) and will maintain that temperature for 9 minutes. This option is available in Heavy and Normal Cycles.

Recommended Cycle for typical use:

Only these sanitization cycles have been designed

The Normal cycle with its factory default options to meet NSF requirements. of normal temperature and heated dry together provide the best all around performance. This cycle The cycle time will be extended until the proper water temperature is reached. Washing action will selection is recommended for everyday use and is continue during the water heating delay. For best suitable for a large range of both dish load sizes results, the incoming water temperature should be and food quantities remaining on those dishes. at least 120F (49C).

The sanitize criteria may not be satisfied if there

Option Selections is an interruption of the cycle, power failure or if the incoming water temperature is below 120F

Wash Pressure

The programmed cycles default to the surge

To turn off the SANITIZE option, press the Wash pressure option which varies the pressure optimally Temp pad. The SANITIZE light will turn off. for the cycles intended normal use. If a very low

spray is desired, press the WASH PRESSURE pad.

Due to wash cycle optimization, some pressure options are not selectable in all wash cycle.

OPERATING INSTRUCTIONS

The HEAT DRY option in combination with rinse aid will enhance drying performance. HEAT DRY option is available on all cycles.

Delay Start

The DELAY START option allows you to automatically delay starting your dishwasher from

1-24 hours.

Select your desired cycle and options, then press the DELAY START pad until the desired delay

The AIR DRY option will reduce temperature in the time displays in the status window. The LEDs of selected cycle and options are illuminated. The hot rinse of the selected wash cycle. This option will slightly decrease energy usage but will increase status window displays the delay time and then displays Press Start. the likelihood that dishware will not be dry.

To start the delay countdown, press START/

CANCEL pad and close door immediately.

The status window displays Close after the

Child Lock Controls

To prevent children from accidentally changing the START/CANCEL pad is pressed.

A tone will sound indicating that the countdown dishwasher cycle or starting the dishwasher, lock has started after the door is closed. The selected the dishwasher controls by pressing the DELAY cycle starts when the countdown is completed.

START pad until the status window displays loc.

To unlock the controls, press the DELAY START

Opening the door during cycle pad until loc is no longer displayed in the status

If door is opened while a cycle is running or delay is counting down, the dishwasher will stop running.

The LEDs of selected cycle and options are

To Cancel a Cycle and Delay Start illuminated, the status window displays the

Both running cycle and delay countdown can be remaining cycle time or delay time and displays cancelled at any time.

Press Start.

Open the dishwasher door and press the START/

To resume, press START/CANCEL pad and close

CANCEL pad until you hear a tone. The running the dishwasher door immediately. The status cycle or delay countdown is cancelled. window displays Close after the START/CANCEL

If desired, a new cycle can now be selected, by pad is pressed. pressing START/CANCEL pad and closing the door

A tone will sound indicating that the dishwasher immediately, the new cycle will begin. will begin running from the point of interruption