GE® Built-In Dishwasher GSD2100NCC user guide

Heated dry option.
Turned ON or OFF during the wash cycle.

(on some models)

Troubleshooting Tips

Energizes the heater to boost water temperature in prewash and main wash fill cycles. Recommended for use with heavily soiled dishes. Option may be turned ON or OFF during the wash cycle.

HEATED DRY

Shuts off the drying heat option. Dishes air dry naturally and energy is saved. Open the dishwasher door to speed drying.

HEATED DRY

Turns the heater on for fast drying. This cycle will extend the time to your wash cycle by 30 minutes.

DO NOT use with RINSE ONLY cycle.

(electronic models

DELAY HOURS

When the LOCK pad is touched twice within 3 seconds, all pads become inoperative. You can lock the controls to prevent any selections from being made. Or you can lock the controls after you have started a cycle or selected

DELAY START so the cycle or DELAY START is not interrupted.

Children cannot accidentally start dishwasher by touching pads with this option selected.

To unlock the dishwasher after it has been locked, touch the LOCK pad twice within 3 seconds. The light above the LOCK pad will turn off.

Delays the start of a wash cycle for up to 8 hours.

(on some models)

Touch RESET to cancel options.

(timer models)

START/RESET

Consumer Support

(electronic models)

Touch START/RESET one time to start dishwasher cycle. Touch START/RESET a second time to pump out and then turn off the dishwasher. Do not touch START/RESET more than one time unless you intend to end the cycle.

Control Settings

Cycle Chart

Water Usage (gal.)

Cycle Time (min.)

Hot Start Option1

Heavy Wash

Normal Wash

Rinse Only

Plate Warmer

Hot PreWash Option1

Normal Wash

Hot Start Option1

Heavy Wash

Normal Wash

Light Wash

Rinse Only

Plate Warmer

Hot PreWash Option1

Heavy Wash

Normal Wash

Water Saver

Rinse Only

Hot PreWash Option1

Heavy Wash

Normal Wash*

Water Saver*

Rinse Only*

Plate Warmer

Hot Start Option1

Pots & Pans

Normal Wash*

Light Wash*

Rinse Only*

Plate Warmer

Hot Start Option1

Heavy Wash

Normal Wash*

Rinse Only*

Plate Warmer

Hot Start Option1

Pots & Pans

Normal Wash*

Rinse Only*

Plate Warmer

Hot Start Option1

Pots & Pans

Heavy Wash

Normal Wash*

Light Wash*

Rinse Only*

Plate Warmer

Pots & Pans

Heavy Wash

Normal Wash

China/Crystal

Rinse Only

Troubleshooting Tips

Operating Instructions

Safety Instructions

Hot Start Option adds water amount and cycle time shown when selected.

* Normal Wash button should be pushed to run this cycle.

Consumer Support

NOTE: Not all models have every cycle listed.

You can locate your model number on the left tub wall just inside the door. Throughout this manual, features and appearance may vary from your model.

Please match the control panel for your unit to a similar control panel below.

Consumer Support

Troubleshooting Tips

Operating Instructions

Safety Instructions

About the dishwasher control panel

Rinse Only

For rinsing partial loads that will be washed later. Do not use detergent.

1 Make sure HEATED DRY is not selected.

2 Be sure the door is unlatched.

3 Slowly turn the Dial to RINSE ONLY.

4 Latch the door to start the cycle.

Safety Instructions

Operation of models with cycle dial

Plate Warmer or Drying

For warming clean dishes and serving plates. This cycle will take approximately 39 minutes.

Slowly turn the Dial to PLATE WARMER or

Operating Instructions

1 Load clean dishware to be warmed.

2 Select HEATED DRY ON.

3 Be sure the door is unlatched.

5 Latch the door to start the cycle.

Hot Start or Hot Prestart Option

Preheats wash water. the HOT START or HOT PRESTART cycle and any other option on the push button pad.

Be sure the door is unlatched. turn the Dial to HOT START or

HOT PRESTART.

4 Latch the door to start the cycle.

Short Wash or Light Wash or Water Saver

1 Be sure the door is unlatched. turn the Dial to SHORT WASH,

LIGHT WASH or WATER SAVER.

Troubleshooting Tips

For quickly washing loads of everyday dishes with light to medium soils that have not dried on.

3 Latch the door to start the cycle.

Start Delay (on some models)

The START DELAY will allow you to delay the start time of any cycle automatically up to 6 hours.

1 Be sure the door is unlatched. turn the Dial to the desired time.

The CYCLE ON light will come on.

2 Select the wash cycle and option you want.

4 Latch the door to start the