Automatic Dishwashing
Detergent has been approved for use in all GE dishwashers.
? Load light, plastic items so they will not become dislodged and drop to the bottom of the dishwasher they might come into contact with the heating element and be damaged.
Read and follow this
Safety Information carefully.
Customer Service
SAVE THESE INSTRUCTIONS
Safety Information
About the dishwasher control panel.
You can locate your model number on the tub wall just inside the door.
Throughout this manual, features and appearance may vary from your model.
LOAD SELECTIONS
POTS NORMAL
HI TEMP HI TEMP HEATED
Operating Instructions
Control Settings
Load Selections
The light above the selected pad will be ON to indicate which LOAD SELECTION has been selected.
POTS & PANS For heavily soiled dishes or cookware with dried-on or baked-on soils. Everyday dishes may be included. This cycle will not remove burned-on foods.
NORMAL For loads of everyday dishes and glassware with medium soils.
LIGHT WASH For dishes with light soils.
CHINA CRYSTAL For lightly soiled china and crystal.
Customer Service
Troubleshooting Tips
RINSE ONLY For rinsing partial loads that will be washed later. Do not use detergent with this cycle.
Safety Information
The light above the selected pad will be ON to indicate which OPTION has been selected.
HI TEMP Turns on the heater in all postrinse and final rinse cycles to help prevent spotting
RINSE on dishware. This option may be turned ON or OFF during the wash cycle.
HI TEMP Energizes the heater to boost water temperature in all prewash and main wash fill
WASH cycles. Recommended for use with heavily soiled dishes. Option may be turned ON or OFF during the wash cycle.
Operating Instructions
HEATED DRY Shuts off the drying heat option. Dishes air dry naturally and energy is saved. You can prop the door open after the CLEAN light illuminates.
HEATED DRY Turns the heater on for fast drying. This cycle will extend the time to your wash cycle by 30 minutes. NOTE: Cannot be selected with RINSE ONLY cycle.
LOCK When the LOCK pad is touched twice within 3 seconds, all pads become inoperative.
You can lock the controls to prevent any selections from being made. Or you can lock the controls after you have started a cycle or selected DELAY START so the cycle or DELAY
START is not interrupted.
Children cannot accidentally start dishwasher by touching pads with this option selected.
To unlock the dishwasher after it has been locked, touch the LOCK pad twice within
3 seconds. The light above the LOCK pad will turn off.
Troubleshooting Tips
DELAY START You can delay the start of a wash cycle for up to 8 hours. Press the DELAY START pad to choose the number of hours you want to delay the start of the cycle. The machine will count down and start automatically at the correct time. Pressing the
START/RESET button will cancel the DELAY START selection.
NOTE: If you forget to latch the door a reminder signal will beep until you do so.
RESET To change a cycle after washing starts, touch the START/RESET pad to cancel the cycle. After water is pumped out and the motor stops, you can reprogram and restart the dishwasher. This will take approximately 90 seconds.
Close and latch the door. Touch the START/RESET pad to begin the cycle. Water fill begins and approximately 40 seconds later the wash action begins.
NOTE: The dishwasher remembers your last cycle so you dont have to reprogram each time. When the dishwasher is loaded and the door latch is in the locked position, the control panel lights will be ON and display the last settings you
Customer Service
If you dont want to change any of the settings, simply touch the START/RESET pad to begin the cycle.
Also, if a power failure occurs, NORMAL and HEATED DRY will automatically be programmed. Make any new selections and touch the START/RESET pad to begin the cycle.
This light is illuminated when a wash cycle is complete. The light will stay ON until the door is opened.
Safety Information
Flashing display lights.
Operating Instructions
What It Means
What To Do
This is normal.
The START/RESET pad has been pressed.
Allow the dishwasher to drain and reset before you start a new wash
Control Error
Press the START/RESET pad to turn off the beeper. If the CLEAN light continues to flash, call for service.
Control Error
Press the START/RESET pad to turn off the beeper and the dishwasher will attempt to reset. Then restart the wash cycle. If this error continues, call for service.
Troubleshooting Tips
Customer Service
Safety Information
About the dishwasher cycle sequence.
You can locate your model number on the tub wall just inside the door.
Throughout this manual, features and appearance may vary from your
Cycle Sequence
(approx.) (approx.)
POTS & PANS
Prewash Prewash Prewash Main wash Postrinse Postrinse Final rinse
Prewash Prewash Main wash Postrinse Postrinse Final rinse
LIGHT WASH
Prewash Main wash Postrinse Postrinse Final rinse
CHINA CRYSTAL 8.3 gal.
Prewash Main wash Postrinse Postrinse Final rinse
Operating Instructions
RINSE ONLY
Cycle Sequence
Drying Options:
HEATED DRY ON. Available on all wash cycles except RINSE ONLY.
Add approximately 30 minutes to the cycle.
HEATED DRY OFF. Drying heater is turned off. Dishes dry naturally.
Troubleshooting Tips
Customer Service
Safety Information
Using the dishwasher.
Check the Water Temperature
Operating Instructions
The entering water must be at least 120F. and not more than
