GE Profile™ Built-In Dishwasher PDW7300GWW user guide

ExtraClean wash with 3 direct feed wash arms.
NORMAL WASH Heavy 9.9 gal., 74 min.

Medium 7.0 gal., 61 min.

Light 5.6 gal., 48 min.

This cycle is for medium/heavily soiled dishes and glassware.

Safety Instructions

SPEED CYCLE

Heavy 9.3 gal., 36 min.

Medium 7.2 gal., 36 min.

Light 5.7 gal., 33 min.

This cycle is for everyday dishes and glassware.

CHINA CRYSTAL Heavy 10.0 gal., 49 min.

Medium 7.2 gal., 36 min.

Light 7.2 gal., 36 min.

This cycle is for lightly soiled china and crystal.

GLASSES Heavy 10.0 gal., 45 min.

(on some models) Medium 7.2 gal., 33 min.

Light 7.2 gal., 32 min.

This cycle is specifically designed for glasses.

NOTE: This dishwasher is equipped with an ExtraClean Sensor with automatic temperature control; therefore cycle length and time may vary depending on soil and temperature conditions.

NOTE: Only the Anti-Bacteria cycle has been designed to meet the requirements of Section 6,

NSF 184 for soil removal and sanitization efficacy.

Enhancements

The light above the selected pad will be ON to indicate which ENHANCEMENT has been selected.

Operating Instructions

RINSE ONLY Heavy 2.9 gal., 7 min.

Light 1.4 gal., 3 min.

For rinsing partial loads that will be washed later. Do not use detergent with this cycle.

PRE For use with heavily soiled and/or dried-on, baked-on soils. This option MUST be selected

WASH PRIOR to starting the cycle. This option adds 16 minutes to the cycle time. NOTE: Cannot be selected with RINSE ONLY cycle.

Troubleshooting Tips

HEATED DRY Shuts off the drying heat option. Dishes air dry naturally and energy is saved. For faster air dry,

Light OFF you can prop the door open after the CLEAN light illuminates.

HEATED DRY Turns the heater on for fast drying. This will extend the time to your wash cycle by 8 minutes

Light ON for the SPEED CYCLE and 30 minutes for all other cycles. NOTE: Cannot be selected with

RINSE ONLY cycle.

LOCK You can lock the controls to prevent any selections from being made. Or you can lock the controls after you have started a cycle.

Children cannot accidentally start dishwasher by touching pads with this option

To unlock the dishwasher controls, press and hold the HEATED DRY pad for 3 seconds. To lock the dishwasher, press and hold the HEATED DRY pad for 3 seconds. The light above the LOCK pad will turn off.

ADDED HEAT When selected, the cycle will run longer with heating elements on to improve both wash and dry performance. NOTE: Cannot be selected with RINSE ONLY cycle.

RESET To change a cycle after washing starts, touch the START/RESET pad to cancel the cycle. The

START/RESET light will flash while the water is pumped out if needed. This takes approximately

90 seconds. When the light stops flashing, the dishwasher can be reprogrammed and restarted.

Consumer Support

DELAY HOURS You can delay the start of a wash cycle for up to 9 hours. Press the DELAY HOURS pad to choose the number of hours you want to delay the start of the cycle; then press START/RESET.

The machine will count down and start automatically at the correct time. Pressing START/RESET a second time will cancel the DELAY START selection. NOTE: If you forget to fully close the door, a reminder signal will beep until you do so.

Operating Instructions

Safety Instructions

About the dishwasher control panel.

Close the dishwasher door and select the cycle and desired enhancements. Touch the

START/RESET pad to begin the cycle. Water fill begins, and approximately 60 seconds later the wash action begins.

NOTE: The dishwasher remembers your last cycle so you dont have to reprogram each time. When the dishwasher door is fully closed, the control panel lights will display the last settings you selected.

If you dont want to change any of the settings, simply touch the START/RESET pad to begin the cycle.

If the door is closed the indicator lights will turn off if the START/RESET pad is not selected within two minutes. To activate the display, open and close the door or press any pad.

Also, if a power failure occurs, NORMAL and HEATED

DRY will automatically be programmed. Make any new selections and touch the START/RESET pad to begin the cycle.

The CLEAN light is illuminated when a wash cycle is complete. The light will stay ON until the door is opened.

Flashing display lights.

Status Indicator Lights

What It Means

START/RESET

Cycle has been interrupted by pressing the START/RESET pad. Light will quit flashing after the dishwasher automatically drains out the water.

Using the dishwasher.

Check the Water Temperature

Troubleshooting Tips

The entering water should be at least 120F and not more than 150F for effective cleaning and to prevent dish damage. Check the water temperature with a candy or m