GE® 7.0 Cu. Ft. Capacity Coin-Operated Electric Dryer DCCD330EDWC user guide

Reverse-a-door.
? The interior of the machine and the exhaust duct connection inside the dryer should be cleaned at least once a year by a qualified technician. See the Care and Cleaning section.

Do not use any type of spray cleaner when cleaning dryer interior. Hazardous fumes or electrical shock could occur.

Operating Instructions

? If yours is a gas dryer, it is equipped with an automatic electric ignition and does not have a pilot light. DO NOT ATTEMPT TO LIGHT WITH

A MATCH. Burns may result from having your hand in the vicinity of the burner when the automatic ignition turns on.

? You may wish to soften your laundered fabrics or reduce the static electricity in them by using a dryer-applied fabric softener or an anti-static conditioner. We recommend you use either a fabric softener in the wash cycle, according to the manufacturers instructions for those products, or try a dryer-added product for which the manufacturer gives written assurance on the package that their product can be safely used in your dryer. Service or performance problems caused by use of these products are the responsibility of the manufacturers of those products and are not covered under the warranty to this appliance.

WHEN NOT USING YOUR DRYER

? Grasp the plug firmly when disconnecting this appliance to avoid damage to the cord while pulling. Place the cord away from traffic areas so it will not be stepped on, tripped over or subjected to damage.

? Before discarding a dryer, or removing it from service, remove the dryer door to prevent children from hiding inside.

? Do not tamper with controls.

Care and Cleaning

? Do not attempt to repair or replace any part of this appliance or attempt any servicing unless specifically recommended in this Owners Manual or in published user-repair instructions that you understand and have the skills to carry out.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

Consumer Support

Safety Instructions

Reversing the door.

Tools needed:

Consumer Support

Care and Cleaning

Operating Instructions

? Standard #2

Phillips screwdriver

? Tape-tipped putty knife

Open the door and remove the filler plugs opposite the hinges. With the door completely open, remove the bottom screw from each hinge on the dryer face. Insert these screws about halfway into the TOP holes, for each hinge, on the opposite side (where you removed the filler plugs).

Apply firm pressure to get the screw started in new holes.

Loosen top screw from each hinge on the dryer face halfway. With one hand holding the top of the door and the other hand holding the bottom, remove the door from the dryer by lifting it UP and OUT.

Rotate the door 180. Insert it on the opposite side of the opening by moving the door IN and DOWN until the top hinge and the bottom hinge are resting on the top screws inserted in step 1.

Remove the remaining screws from the side of the opening from which the door was removed. With these screws secure each hinge at the bottom.

Tighten the two top screws of each hinge. Reinsert the plastic plugs on the side from which the door was removed.

Countdown display. (DCCD models only)

Safety Instructions

The countdown display shows the remaining operating time as well as the current drying cycle. The display board is configured for a 45-minute dry time at the factory to correspond with the 45-minute timer cam pre-installed in the coin box. If the timer cam is modified for another operating duration, the dip switches on the display board should be set as follows:

DIP SWITCH NUMBERS

Operating Instructions

DRYING TIME (minutes)

NOTE: This display does not accumulate time. See the following examples of display possibilities.

DIP SWITCH SETTING (min)

COIN SLIDE ACTUATIONS

DISPLAY READING (min)

45 to 0, then blank

45 to 1, then 1 for next 45 min., then 0 and blank

99 for 21 minutes, then 98 to 0, then blank

Care and Cleaning

Consumer Support

Safety Instructions

Venting the dryer.

For the best drying performance, the dryer needs to be properly vented. The dryer will use more energy and run longer if it is not vented to the below specifications. Carefully follow the details on Exhausting in the

Installation Instructions.

? Use only rigid metal 4? diameter ductwork inside the dryer cabinet. Use only rigid metal or flexible metal 4? diameter ductwork for exhausting to the outside.

? Do not use plastic or other combustible du