GE Café™ Series 30" Commercial Hood CV936EKDS user guide

Removable grease filter.
Stainless Steel Surfaces (on some models)

Do not use a steel wool pad; it will scratch the

Use only a liquid cleanser free of grit and rub in the direction of the brush lines with a damp soft sponge.

To clean the stainless steel surface, use warm sudsy water or a stainless steel cleaner or polish. Always wipe the surface in the direction of the brush line. Follow the cleaner instructions for cleaning the stainless steel surface. Cleaners with oxalic acid such as Bar Keepers

Friend Soft Cleanser will remove surface rust, tarnish, and small blemishes. To receive a

$2.00 coupon for a trial sample of Bar Keepers Friend Soft

Cleanser follow the link below or scan the QR Code.

To inquire about purchasing stainless steel appliance cleaner or polish, or to find the location of a dealer nearest you, please call our toll-free number:

National Parts Center

800.626.2002

Painted Surfaces (on some models)

Do not use a steel wool pads or other abrasive cleaners; they will scratch the surface.

Clean grease-laden surfaces of the hood frequently. To clean the hood surface, use a hot, damp cloth with a mild detergent suitable for painted surfaces. About one tablespoon of ammonia may be added to the water. Use a clean, hot, damp cloth to remove soap. Dry with a dry, clean cloth.

NOTE: When cleaning, take care not to come in contact with filters and other surfaces.

When cleaning the hood surfaces, be certain that you do not touch the light with moist hands or cloth. A warm or hot light may break if touched with a moist surface. Always let the light cool completely before cleaning around it.

49-80520-9

Be sure electrical power is off and all surfaces are cool before cleaning or servicing any part of the vent hood.

NOTE: The glass cover should be removed only when cold. Wearing latex gloves may offer a better grip.

CAUTION Before replacing your light bulb, disconnect the electrical power to the hood at the main fuse or circuit breaker panel.

Be sure to let the light cover and bulb cool completely.

For your safety, do not touch a hot bulb with bare hands

or a damp cloth.

Receptacle

To remove:

1. Turn the glass cover counterclockwise until the glass cover clears the

2. Using gloves or a dry cloth, remove the bulb by pulling it straight out.

To replace:

1. Use a new 12-volt, 20-watt (maximum)

Halogen bulb for a G-4 base.

2. Using gloves or a dry cloth, remove the new bulb from its packaging. NOTE: Do not touch the new halogen bulb with bare fingers. Touching the bulb with bare fingers will significantly reduce the life of the bulb.

3. Push the bulb straight into the receptacle all the way.

4. Place the glass cover onto the socket and turn clockwise until secure. For improved lighting, clean the glass cover

Receptacle frequently using a damp cloth. This should be done when the hood is completely cool.

5. Reconnect electrical power to the hood.

CARE AND CLEANING: Lights

Glass cover

49-80520-9

INSTALLATION INSTRUCTIONS

Installation

Instructions

Range Hoods

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANT Save these instructions for local inspectors use.

IMPORTANT Observe all governing codes and ordinances.

Note to Installer Be sure to leave these instructions with the Consumer.

Note to Consumer Keep these instructions for future reference.

Skill level Installation of this vent hood requires basic mechanical and electrical skills.

Completion time Approximately 1 to 3 hours

Proper installation is the responsibility of the installer.

Product failure due to improper installation is not covered under the Warranty.

CAUTION Due to the weight and size of these vent hoods and to reduce the risk of personal injury or damage to the product, TWO PEOPLE

ARE REQUIRED FOR PROPER INSTALLATION.

FOR YOUR SAFETY

WARNING Before beginning the installation,

WARNING TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

A. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.

B. Sufficient air is needed for proper combustion and exhausting of gases through the flue

(chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturers guidelines and safety standards such as those published by the National Fire

Protection Association (NFPA), the American

Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE) and the local code authorities.

C. When cutting or drilling into wall or ceiling, do not damage electri