GE® 7.4 cu. ft. Capacity Smart aluminized alloy drum Gas Dryer with HE Sensor Dry GTD75GCSLWS user guide

Damp Alert.
Cycle is paused. The cycle may be re-started by pressing the Start button.

(on some models)

Controls

Will allow your appliance to communicate with your smartphone for remote appliance monitoring control and notifications

The dryer is locked - will blink once if you press any button or turn the cycle knob.

Sensing

Indicates the dryer is sensing the level of dampness to determine estimated cycle time remaining.

Clean Lint Filter

The Clean Lint Filter light will stay on for 15 seconds after the cycle stops.

Control Lock

You can lock the controls to prevent any selections from being made. Or you can lock the controls after you have started a cycle.

Children cannot accidentally start the dryer by touching buttons with this option selected.

To lock/unlock the dryer controls, press and hold the Extended Tumble and - (minus) buttons for 3 seconds. The control lock icon will flash while locking/unlocking, stay on when locked, and turn off when unlocked.

NOTE: The Power button can still be used when the machine is locked.

Operating instructions

Drying Cycles - S

ensor cycles automatically determine fabric dryness.

Timed cycles run for the selected time.

Steam Dewrinkle For use with larger loads than Steam Refresh. Ideal for loads left in the dryer for an extended time.

(on some models)

Steam Dewrinkle is recommended for 9-13 garments

NOTE: Steam cycles are not intended for use with towels.

Important - the temperature setting must be set to HIGH and water must be turned on

before running the Steam Refresh cycle.

Steam Refresh For slightly wrinkled dry garments. Significantly reduces wrinkles. After the Steam Refresh cycle,

(on some models) the unit will beep (if Signal is selected) and display 00.

Steam Refresh is recommended for 3-5 garments

NOTE: Steam cycles are not intended for use with towels.

NOTE: A single extremely light fabric item may need to have an additional item included in

the Steam Refresh cycle to achieve optimum results.

Important - the temperature setting must be set to HIGH and water must be turned on

before running the Steam Refresh cycle.

Sanitize or This option reduces certain types of bacteria including: Staphylococcus aureus, Pseudomonas

Anti-Bacterial aeruginosa and Klebsiella pneumoniae. The anti-bacterial process occurs when high heat is used

(depending during a portion of the drying cycle. on model) NOTE: Do not use this cycle on delicate fabrics.

Bulky Items For large coats, bed spreads, mattress covers, sleeping bags, and similar large/bulky items such as

blankets, comforters, jackets, and small ruga.

Towels/Sheets For most towels and linens.

Cottons For cottons and most linens.

Mixed Load For loads consisting of cottons and poly-blends.

Casuals For wrinkle-free, permanent press, delicate items and knits.

Delicates For delicate items, special-care fabrics and knits.

Speed Dry For small loads that are needed in a hurry, such as sport or school uniforms. Can also be used if the previous

cycle left some items damp, such as collars or waistbands. NOTE: On some models, the time remaining in

the cycle will show counting down in the display.

Jeans For jeans.

Timed Dry Set the Cycle Selector at the desired drying time.

Provides 10 minutes of warming time to warm up clothes.

Provides 10 minutes of tumbling time with no heat.

Available for Bulky Items, Towels/Sheets, Cottons, Mixed Load, Jeans, Casuals and Delicates. When the eDry button is pressed, cycle settings change to reduce the total energy consumption of the selected sensor cycle. NOTE: Cycle times will change when eDry is selected. The eDry option will default to on for Cottons. For optimal energy savings, turn eDry on.

For optimal drying times, turn eDry off. NOTE: Energy savings will vary across loads and cycles.

Individual settings for cycle minutes (Time), dryness level (Level) and temperature (Temp) can be set from the minimum

(lowest in column) to maximum (highest in column). In general, the higher up the column, the more energy will be used.

NOTE: The selected cycle set Time can be further adjusted, in one minute increments, by pressing the Time Adjust + (plus) and - (minus) buttons.

Dryness Level-Selection only used for Sensor cycles. Timed cycles run for the selected time.

Use for heavy-duty or mixed type fabrics.

Use for a normal dryness level suitable for most loads. This is the preferred cycle for energy savings.

Use for lighter fabrics.

For leaving items partially damp.

Temperature

High For regular to heavy cottons.

NOTE: Steam Dewrinkle and Steam Refresh require the High temperature setting.

For synthetics, blends, delicates and items labeled permanent press.

For delicates, synthetics and items labeled tumble dry low.

For fluffing items without heat. For use only with the Air Fluff cycle.

Extended Tumble

Use this option to minimize the wrinkles in clothes. It provides 1 hour of no-heat tumbling after the clothes are dry. If you are using the cycle Signal Adjust or Volume and you select the Extended Tumble option, a signal will sound at the end of the drying time and several times during the Extended Tumble cycle. This will remind you that it is time to remove the clothes.

Damp Alert

This option causes the dryer to beep when clothes have dried to a damp level. Remove items that you wish to hang dry. The

Damp Alert will only beep when this option is selected (but the dry cycle will keep running). Removing clothes and hanging them when they are damp, can reduce the need to iron some items. The light beside the button will be lit when Damp Alert is on.

Drum Light

The drum light will turn on if the Damp Alert button is pressed for 3 seconds or the door is opened. It will turn off when the door is shut, the Damp Alert button is pressed again for 3 seconds or after 5 minutes if the door is left open.

Press the Delay Dry button to set the delay start time in 1 hour increments up to 24 hours, and then back to clear (0 hours).

After selecting the delay start time, press Start and the delay time will count down the time remaining until the cycle starts.

NOTE: To set the amount of delay time faster, you can press and hold the Delay Dry b