FAN only mode.
In FAN only mode, the fan will stay in the LOW speed setting for 8 hours. After 8 hours, the air conditioner will resume the settings that were in place before the SLEEP mode pad was pressed.
In COOL mode, the fan will stay in the LOW speed setting for 8 hours from the time the SLEEP mode pad was pressed. The air conditioner will also raise the set point 2F in 30 minutes and 2F more in another 30 minutes where it will remain for the
QH[WKRXUV$IWHUKRXUVWKHDLUFRQGLWLRQHUZLOO resume the settings that were in place before the
SLEEP mode pad was pressed.
While the unit is in SLEEP mode, pressing any pad will return it to the settings that were in place before the SLEEP mode pad was pressed.
Control Display On and Off
To reduce brightness during sleeping hours, this air conditioner control display has an automatic off feature where the control display will turn off completely after 5 minute of inactivity. To illuminate the control interface, press any button on the control display or remote control. The control display will illuminate all previously illuminated
LEDs. The control interface will now respond to any prescribed button press after it is illuminated.
Press and hold the FAN+MODE buttons simultaneously to toggle this feature ON or OFF.
The LEDs will now stay ON anytime the unit is
Control Sound On and Off
This air conditioner will make a beep when the buttons on the control are pushed or if the unit receives a command from the mobile app or remote control. To silence these beeps, simultaneously press the FAN and - buttons for 3 seconds. Press these buttons again to toggle the sound back on.
USING THE AIR CONDITIONER
Using the Air Conditioner
Remote Control
?7RHQVXUHSURSHURSHUDWLRQDLPWKHUHPRWHFRQWURODW the signal receiver on the air conditioner.
?0DNHVXUHQRWKLQJLVEHWZHHQWKHDLUFRQGLWLRQHUDQG the remote control that could block the signal.
?7KHUHPRWHFRQWUROVLJQDOKDVDUDQJHRIXSWR
?0DNHVXUHEDWWHULHVDUHIUHVKDQGLQVWDOOHGFRUUHFWO
as indicated on the remote control.
?5HPRWHFRQWDLQVDPDJQHWDOORZLQJLWWRDWWDFKWR metal surfaces.
8VHWKH&RROPRGHDW/RZ0HG+LJKRU$XWR)DQ
6SHHGIRUFRROLQJ8VHWKH7HPSHUDWXUH,QFUHDVH
Decrease pads to set the desired temperature between
64F and 86F in 1F increments.
An electronic thermostat is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the set level of comfort. Set the thermostat at a lower number and the indoor air will become cooler. Set the thermostat at a higher number and the indoor air will become warmer.
49-5000434 Rev. 2
NOTE: If the air conditioner is off and is then turned on while set to a Cool setting or if turned from a fan setting
WRD&RROVHWWLQJLWPDWDNHDSSUR[LPDWHOPLQXWHVIRU the compressor to start and cooling to begin.
Cooling Descriptions
For Normal CoolingSelect the Cool mode and High or Med fan with a middle set temperature.
For Maximum CoolingSelect the Cool mode and
High fan with a lower set temperature.
For Quieter and Nighttime CoolingSelect the Cool mode and Low fan with a middle set temperature.
USING THE AIR CONDITIONER
Using the Air Conditioner
This mode optimizes the cooling power of your air conditioner, thereby saving you energy. Once the set point temperature has been reached, the fan will cycle off to save energy. The fan will cycle back on periodically to insure all cooling capacity in the system is used. This mode is the default mode for the unit. Each time the unit is powered off, it will restart in ECO mode ON. This includes Delay timer mode. The first time the unit is turned on, the settings will be 70 and Low fan. You can adjust the fan speed and temperature to your personal
ECO ONHelps minimize electricity use. It is normal for the fan to cycle off and then back on in this mode.
7KLVRQRIIFFOHFDQUHSHDWPXOWLSOHWLPHV%HFDXVH the fan will cycle off, you may notice a variation in room temperature and humidity.
ECO OFFWhen this mode is not engaged, the fan will run continuously, and in Cool mode the compressor will cycle on and off to maintain room temperature.
Fan Only Mode
8VHWKH)DQ2QO0RGHDW/RZ0HGRU+LJKIDQVSHHG to provide air circulation and filtering without cooling.
Since fan-only settings do not provide cooling, a Set temperature cannot be entered. The room temperature will appear in the display.
NOTE: Auto Fan Speed cannot be used when in the Fan
Only Mode.
Auto Fan Speed
Set to Auto fan speed for the fan speed to automatically set to the speed needed to provide optimum comfort settings with the set temperature.
If the room needs more cooling, the fan speed will automatically increase. If the room needs less cooling, the fan speed will automatically decrease.
NOTE: Auto Fan Speed cannot be used when in the Fan
Only Mode.
Power Outage Recovery Feature
In the case of a power outage or interruption, the unit will automatically restart in the settings last used after the power is restored.
Air Direction
8VHWKHOHYHUWRDGMXVWWKHDLUGLUHFWLRQOHIWDQGULJKW
49-5000434 Rev. 2
Grille and Case
Turn the air conditioner off and remove the plug from the wall outlet before cleaning.
To clean, use water and a mild detergent. Do not us
