GE® 230 Volt Electronic Room Air Conditioner AEH25DM user guide

Slide-out chassis.
Instructions

Delay 124hr

Shows the room temperature or time remaining on the Delay timer. Shows the Set temperature while setting the temperature in

Cool or Energy Saver modes. The Set light will turn on while setting.

NOTE: The display will change to show the room temperature after settings have been made. To recall the Set temperature, press the

Temp Increase ? or Decrease ? pads.

Temp Increase ? /Decrease ? Pads

Use to set temperature when in Cool or Energy

Saver mode. The Set light will turn on while

Delay Timer Increase ? (+) /Decrease ? ()

Each touch of the Increase ? / Decrease ? pads on the unit or the Increase + / Decrease pads on the remote control will set the delay time when using the Delay 124hr timer ( ).

The Set light will turn on while setting.

Fan Speed Pads

Use to set the fan speed to Low, Med, High or Auto on the unit. NOTE: On the remote control, use the fan speed Increase + /

Decrease pads to set the fan speeds to Low,

Med or High. Use the Auto pad to turn Auto

Use to set the air conditioner to Cool, Energy

Saver or Fan Only mode.

Delay Pads

Delay ONWhen the air conditioner is off, it can be set to automatically come on in 1 to 24 hours at its previous mode and fan settings.

Delay OFFWhen the air conditioner is on,

it can be set to automatically turn off in 1 to

How to set:

Press the Delay 124hr pad on the unit or the pad on the remote control. Each touch of the Increase ? / Decrease ? pads on the unit or the Increase + / Decrease pads on the remote control will set the timer in

1-hour intervals. The Set light will turn on while setting.

To review the remaining time on the Delay

124hr timer, press the Delay 124hr pad on the unit or the pad on the remote control. Use the Increase ? / Decrease ? pads on the unit or the Increase + / Decrease pads on the remote control to set a new time if desired.

To cancel the timer, press the Delay 124hr pad until the light on the Delay 124hr pad goes off.

CIRCULAIRE Pad

Turn on to provide continuous side-to-side air circulation.

For fixed side-to-side air direction, turn on until the desired air direction is obtained, then turn it off.

Do Not Operate in Freezing Outdoor Conditions

This cool-only air conditioner was not designed for freezing outdoor conditions. It must not be used in freezing outdoor conditions.

An electronic thermostat is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the set level of comfort.

Set the thermostat at a lower number and the indoor air will become cooler. Set the thermostat at a higher number and the indoor air will become warmer.

Cooling Descriptions

For Normal CoolingSelect the Cool mode and

High or Med fan with a middle set temperature.

Instructions

Use the Cool mode at Low, Med, High or Auto Fan

Speed for cooling. Use the Temperature Increase ? /

Decrease ? pads to set the desired temperature between 64F and 86F in 1F increments.

For Maximum CoolingSelect the Cool mode and High fan with a lower set temperature.

For Quieter & Nighttime CoolingSelect the

Cool mode and Low fan with a middle set temperature.

Care and Cleaning

NOTE: If the air conditioner is off and is then turned on while set to a Cool setting or if turned from a fan setting to a Cool setting, it may take approximately 3 minutes for the compressor to start and cooling to begin.

Energy Saver Mode

Controls the fan.

Installation

Instructions

ONThe fan will cycle on and off with the compressor. This results in wider variations of room temperature and humidity. Normally used when the room is unoccupied. NOTE: The fan may continue to run for a short time after the compressor cycles off.

OFFThe fan runs all the time, while the compressor cycles on and off.

Auto Fan Speed

Use the Fan Only Mode at Low, Med or High fan speed to provide air circulation and filtering without cooling. Since fan only settings do not provide cooling, a Set temperature cannot be entered. The room temperature will appear in the display.

Set to Auto fan speed for the fan speed to automatically set to the speed needed to provide optimum comfort settings with the set temperature.

If the room needs more cooling, the fan speed will automatically increase. If the room needs less cooling, the fan speed will automatically decrease.

NOTE: Auto Fan Speed cannot be used when in the

Fan Only Mode.

Power Outage Recovery Feature

In the case of a power outage or interruption, the unit will automatically re-start in the settings last used after the power is restored. If the Delay 124hr feature was set, it will resume countdown. You may need to set a new time if desired.

Remote Control

? To ensure proper operation, aim the remote control at the signal receiver on the air conditioner.

? Make sure nothing is between the air conditioner and the remote control that could block the

? The remote control signal has a range of up to 20 feet.

? Make sure batteries are fresh and installed correctly as indicated on the remote control.

Troubleshooting Tips Consumer Support

Fan Only Mode

NOTE: Auto Fan Speed cannot be used when in the

Fan Only Mode.

Safety Instructions

Safety Instructions

About the controls on the air conditionermodels with control knobs.

Features and appearance will vary.

(on some models)

Consumer Support Troubleshooting Tips

Installation

Instructions

Care and Cleaning

Instructions

TEMPERATURE

High Cool, Med Cool and Low Cool provide cooling with different fan speeds.

Fan settings provide air circulation and filtering without cooling.

NOTE: If you move the mode control from a cool setting to OFF or to a fan setting, wait at least 3 minutes before switching back to a cool setting.

Cooling Descriptions

For Normal CoolingSelect High Cool or Med Cool with the

TEMPERATURE control at midpoint.

For Maximum CoolingSelect High Cool with the TEMPERATURE control at the highest number available on your knob.

For Quieter & Nighttime CoolingSelect Low Cool with the

TEMPERATURE control at midpoint.

TEMP Control

The TEMP control is used to maintain the room temperature.

The compressor will cycle on and off to keep the room at the same level of comfort. When you turn the knob to a higher number, the indoor air will become cooler. Turn the knob to a lower number and the indoor air will become warmer.

CIRCULAIRE

For continuous side-to-side air circulation, set the Circulaire switch to ON.

For fixed side-to-side air direc