GE® ENERGY STAR® 115 Volt Electronic Room Air Conditioner AEL08LV user guide

Non-ozone-depleting refrigerant (R-410A).
While setting the temperature in Cool or Energy

Saver modes. The Set light will turn on while

NOTE: The display will change to show the room temperature after settings have been made.

Temp Increase /Decrease ? Pads

Use to set temperature when in Cool or Energy

Saver mode. The Set light will turn on while

Delay Timer Increase (+) /Decrease ?()

Each touch of the Increase / Decrease? pads on the unit or the Increase + / Decrease pads on the remote control will set the delay time when using the Delay 124hr timer. The

Set light will turn on while setting.

Fan Speed Pads

Use to set the fan speed to Low, Med, High or Auto on the unit. NOTE: On the remote control, use the fan speed Increase + /

Decrease pads to set the fan speeds to Low,

Med or High. Use the Auto pad to turn Auto

Delay ON:KHQWKHDLUFRQGLWLRQHULVRIILWFDQ be set to automatically come on in 1 to 24 hours at its previous mode and fan settings.

Delay OFF:KHQWKHDLUFRQGLWLRQHULVRQ it can be set to automatically turn off in 1 to

How to set:

Press the Delay 124hr pad on the unit or the

Delay pad on the remote control. Each touch of the Increase / Decrease ?pads on the unit or the Increase + / Decrease pads on the remote control will set the timer in 1-hour intervals. The Set light will turn on while setting.

To review the remaining time on the Delay

124hr timer, press the Delay 124hr pad on the unit or the Delay pad on the remote control.

Use the Increase / Decrease?pads on the unit or the Increase + / Decrease pads on the remote control to set a new time if desired.

To cancel the timer, press the Delay 124hr pad

until the light on the Delay 124hr pad goes off.

Reset Filter

LED will turn on when fan has accumulated 250 hours of run time as a reminder to clean filter.

Press Reset Filter to turn off the LED and reset the accumulated run time.

Note: The default temperature reading on the display is degree Fahrenheit ( F). To change the display to degree Celcius (C), press the Temp Increase and Temp Decrease ? buttons together and hold for 3 seconds. Repeat the process to change back to degree Fahrenheit (F)

Do Not Operate in Freezing Outdoor Conditions

This cool-only air conditioner was not designed for freezing outdoor conditions. It must not be used in freezing outdoor conditions.

Remote Control

To ensure proper operation, aim the remote control at the signal receiver on the air conditioner.

? Make sure nothing is between the air conditioner and the remote control that could block the signal.

? The remote control signal has a range of up to 20 feet.

? Make sure batteries are fresh and installed correctly as indicated on the remote control.

? Remote contains a magnet allowing it to attach to metal

Use the Cool mode at Low, Med, High or Auto Fan Speed for cooling. Use the Temperature Increase / Decrease ? pads to set the desired temperature between 64F and 86F in 1F increments.

An electronic thermostat is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the set level of comfort. Set the thermostat at a lower number and the indoor air will become cooler. Set the thermostat at a higher number and the indoor air will become

NOTE: If the air conditioner is off and is then turned on while set to a Cool setting or if turned from a fan setting to a Cool setting, it may take approximately 3 minutes for the compressor to start and cooling to begin.

Cooling Descriptions

For Normal Cooling6HOHFWWKHCool mode and High or Med fan with a middle set temperature.

For Maximum Cooling6HOHFWWKH Cool mode and High fan with a lower set temperature.

For Quieter and Nighttime Cooling6HOHFWWKHCool mode and Low fan with a middle set temperature.

Energy Saver Mode

This mode optimizes the cooling power of your air conditioner, thereby saving you energy. Once the set point temperature has been reached, the fan will cycle off to save energy. The fan will cycle back on periodically to insure all cooling capacity in the system is used. This mode is the default mode for the unit. Each time the unit is powered off, it will restart in Energy Saver mode ON. This includes Delay timer mode. The first time the unit is turned on, the settings will be 70 and Low fan. You can adjust the fan speed and temperature to your personal comfort.

Energy Saver ONHelps minimize electricity use. It is normal for the fan to cycle off and then back on in this mode. This on/off cycle can repeat multiple times. Because the fan will cycle off, you may notice a variation in room temperature and humidity.

Energy Saver OFFWhen this mode is not engaged, the fan will run continuously, and in Cool mode the compressor will cycle on and off to maintain room temperature.

Fan Only Mode

Use the Fan Only Mode at Low, Med or High fan speed to provide air circulation and filtering without cooling. Since fan-only settings do not provide cooling, a Set temperature cannot be entered. The room temperature will appear in the

NOTE: Auto Fan Speed cannot be used when in the

Fan Only Mode.

Auto Fan Speed

Set to Auto fan speed for the fan speed to automatically set to the speed needed to provide optimum comfort settings with the set temperature.

If the room needs more cooling, the fan speed will automatically increase. If the room needs less cooling, the fan speed will automatically decrease.

NOTE: Auto Fan Speed cannot be used when in the Fan Only

Power Outage Recovery Feature

In the case of a power outage or interruption, the unit will automatically restart in the settings last used after the power is restored. If the Delay 124hr feature was set, it will resume countdown. You may need to set a new time if desired.

About the controls on the air conditioner.

Additional important information.

Air Direction

Use the lever to adjust the air direction left and right

Care and cleaning of the air conditioner.

Grille and Case

Turn the air conditioner off and remove the plug from the wall outlet before cleaning.

To clean, use water and a mild detergent. Do not use bleach or abrasives.

Air Filter

The air filter behind the front grille should be checked and cleaned at least every 30 days or more often if necessary.

To remove:

Pull the tab on the right side of the unit until the filter