Saver mode . The Set light will turn on while
Delay Timer Increase ? (+) /Decrease ?()
Each touch of the Increase ?/ Decrease? pads on the unit or the Increase + / Decrease pads on the remote control will set the delay time when using the Delay 124hr timer . The
Set light will turn on while setting .
Fan Speed Pads
Use to set the fan speed to Low, Med, High or Auto on the unit . NOTE: On the remote control, use the fan speed Increase + /
Decrease pads to set the fan speeds to Low,
Med or High . Use the Auto pad to turn Auto
Use to set the air conditioner to Cool, Energy
Saver or Fan Only mode .
Delay ONWhen the air conditioner is off, it can be set to automatically come on in 1 to 24 hours at its previous mode and fan settings .
Delay OFFWhen the air conditioner is on, it can be set to automatically turn off in 1 to
24 hours .
How to set:
Press the Delay 124hr pad on the unit or the
Delay pad on the remote control . Each touch of the Increase ?/ Decrease ?pads on the unit or the Increase +/ Decrease pads on the remote control will set the timer in 1-hour intervals . The Set light will turn on while setting .
To review the remaining time on the Delay
124hr timer, press the Delay 124hr pad on the unit or the Delay pad on the remote control .
Use the Increase ?/ Decrease?pads on the unit or the Increase + / Decrease pads on the remote control to set a new time if desired .
To cancel the timer, press the Delay 124hr pad
until the light on the Delay 124hr pad goes off .
Note: The default temperature reading on the display is degree Fahrenheit ( F) . To change the display to degree Celcius (C), press the Temp Increase ? and Temp Decrease ? buttons together and hold for 3 seconds . Repeat the process to change back to degree Fahrenheit (F)
Features and appearance will vary.
MODE CONTROL
TEMPERATURE CONTROL
Controls (on some models)
Mode Control
High Cool and Low Cool provide cooling with different fan speeds .
Fan settings provide air circulation and filtering without cooling .
NOTE: If you move the mode control from a cool setting to OFF or to a fan setting, wait at least
3 minutes before switching back to a cool
TEMP Control
The TEMP control is used to maintain the room temperature . The compressor will cycle on and off to keep the room at the same level of comfort . When you turn the knob to a higher number, the indoor air will become cooler . Turn the knob to a lower number and the indoor air will become warmer .
Cooling Descriptions
For Normal CoolingSelect High Cool or Low
Cool with the TEMPERATURE control at midpoint .
For Maximum CoolingSelect High Cool with the TEMPERATURE control at the highest number available on your knob .
For Quieter and Nighttime CoolingSelect Low
Cool with the TEMPERATURE control at midpoint .
About the controls on the air conditioner.
Do Not Operate in Freezing Outdoor
Conditions freezing outdoor conditions .
This cool-only air conditioner was not designed for freezing outdoor conditions . It must not be used in
Remote Control
To ensure proper operation, aim the remote control at the signal receiver on the air conditioner .
Make sure nothing is between the air conditioner and the remote control that could block the
The remote control signal has a range of up to 20 feet .
Make sure batteries are fresh and installed correctly as indicated on the remote control .
Remote contains a magnet allowing it to attach to metal surfaces .
Use the Cool mode at Low, Med, High or Auto Fan
Speed for cooling . Use the Temperature Increase ?
/ Decrease ? pads to set the desired temperature between 64F and 86F in 1F increments .
An electronic thermostat is used to maintain the room temperature . The compressor will cycle on and off to keep the room at the set level of comfort . Set the thermostat at a lower number and the indoor air will become cooler . Set the thermostat at a higher number and the indoor air will become warmer .
NOTE: If the air conditioner is off and is then turned on while set to a Cool setting or if turned from a fan setting to a Cool setting, it may take approximately 3 minutes for the compressor to start and cooling to begin.
Cooling Descriptions
For Normal CoolingSelect the Cool mode and
High or Med fan with a middle set temperature .
For Maximum CoolingSelect the Cool mode and High fan with a lower set temperature .
For Quieter and Nighttime CoolingSelect the
Cool mode and Low fan with a middle set temperature .
Energy Saver Mode
Controls the fan .
ONThe fan will cycle on and off with the compressor . This results in wider variations of room temperature and humidity . Normally used when the room is unoccupied . NOTE: The fan may continue to run for a short time after the compressor cycles off.
OFFThe fan runs all the time, while the compressor cycles on and off .
Fan Only Mode
Use the Fan Only Mode at Low, Med or High fan speed to provide air circulation and filtering without cooling . Since fan-only settings do not provide cooling, a Set temperature cannot be entered . The room temperature will appear in the display .
NOTE: Auto Fan Speed cannot be used when in the
Fan Only mode.
Auto Fan Speed
Set to Auto fan speed for the fan speed to automatically set to the speed needed to provide optimum comfort settings with the set temperature .
If the room needs more cooling, the fan speed will automatically increase . If the room needs less cooling, the fan speed will automatically decrease .
NOTE: Auto Fan Speed cannot be used when in the
Fan Only mode.
Power Outage Recovery Feature
In the case of a power outage or interruption, the unit will automatically restart in the settings last used after the power is restored . If the Delay 124hr feature was set, it will resume countdown . You may need to set a new time if desired .
Additional important information.
Air Direction
Use the lever to adjust the air direction left and right
Care and cleaning of the air conditioner.
Grille and Case
