Air Conditioner Controls
Lights beside the touch pads on the air conditioner control panel indicate the selected settings.
Power On/Off
Turns air conditioner on and off.
Displays the temperature setting. Displays hours when setting the timer.
On the remote control, use to set the air conditioner to Cool or Fan mode.
On the air conditioner controls, use to set
Cool or Fan mode at High, Med or Low fan speed. Indicator lights on the air conditioner controls will show the mode and fan speed
Temp Increase + /Decrease Pads
Use to set temperature when in COOL mode.
Fan Speeds
Use to set the fan speed at Low, Med or
To cancel the Delay Timer, press the On pad until
CL appears. Then wait until the display turns off.
2IIWhen the air conditioner is on, it can be set to automatically turn off in half an hour to 24 hours.
Each touch will set the time in half hours up to 10 and then in hours up to 24.
To cancel the Delay Timer, press the Off pad until
CL appears and wait for the set temperature to be displayed. The unit will now resume normal operation.
Reset Filter
LED will turn on when fan has accumulated 250
hours of run time as a reminder to clean filter.
Press Reset Filter to turn off the LED and reset the accumulated run time.
Remote Control Signal Receiver
NOTE: When the air conditioner is turned on, it will automatically start in the setting last used.
2QWhen the air conditioner is off, it can be set to automatically turn on in half an hour to 24 hours at its previous setting. Each touch will set the time in half hours up to 10 and then in hours up to 24.
Remote Control
To ensure proper operation, aim the remote control at the signal receiver on the air conditioner.
Make sure nothing is between the air conditioner and the remote control that could block the
The remote control signal has a range of up to
Make sure batteries are fresh and installed
FRUUHFWOVHHWKH&DUHDQG&OHDQLQJVHFWLRQ
Remote Control
1. Press Cool pad.
2. Press Low, Med or High pads to set desired fan speed.
3. Press the Increase +/ Decrease pads to set the desired temperature 60F to 85F in 1F increments.
Set the thermostat at a higher number and the indoor air will become warmer.
NOTE: If the air conditioner is off and is then turned on while set to Cool, it will take approximately 3 minutes for the compressor to start and cooling to begin.
Cooling Descriptions
Control Panel
)RU1RUPDO&RROLQJSelect the Cool mode and High or
Med fan with a middle set temperature.
1. Press the Mode pad until the Cool indicator light is lit and the Low, Med or High indicator light is lit for the desired fan speed.
)RU0D[LPXP&RROLQJSelect the Cool mode and HIGH fan with a lower set temperature.
2. Press the Increase + / Decrease pads to set the desired temperature 60F to 85F in 1F increments.
A thermostat is used to maintain the room temperature.
The compressor will cycle on and off to keep the room at the set level of comfort. Set the thermostat at a lower number and the indoor air will become cooler.
)RU4XLHWHUDQG1LJKWWLPH&RROLQJSelect the Cool mode and Low fan with a middle set temperature.
NOTE: If you switch from a Cool setting to Off or to a fan setting, wait at least 3 minutes before switching back to a Cool setting.
Use the Fan mode to provide air circulation and filtering without cooling. Since fan-only settings do not provide cooling, a temperature setting will not be displayed.
Remote Control
Press Fan pad. Press Low, Med or High pads to set desired fan speed.
Control Panel
Press the Mode pad until the Fan indicator light is lit and the Low, Med or High indicator light is lit for the desired fan speed.
$ERXWWKHFRQWUROVRQWKHDLUFRQGLWLRQHU+HDW&RRO0RGHOV
Appearance may vary.
Remote Control
Air Conditioner Controls
Lights beside the touch pads on the air conditioner control panel indicate the selected settings.
Turns air conditioner on and off.
Displays the temperature setting. Displays hours when setting the timer.
On the air conditioner controls, use to set
COOL, HEAT or FAN mode. Indicator lights on the air conditioner controls will show the mode selected.
TEMP Increase + /Decrease Pads
Use to set temperature when in COOL or HEAT mode.
FAN Speeds
Use to set the fan speed at LOW or HIGH.
Indicator lights will show the speed selected.
21When the air conditioner is off, it can be set to automatically turn on in half an hour to 24 hours at its previous
Each touch will set the time in half hours up to 10 and then in hours up to 24.
To cancel the On Timer, press the ON pad until CL appears. Then wait until the display turns off.
2))When the air conditioner is on, it can be set to automatically turn off in half an hour to 24 hours. Each touch will set the time in half hours up to 10 and then in hours up to 24.
To cancel the Off Timer, press the OFF pad until CL appears and wait for the set temperature to be displayed. The unit will now resume normal operation.
Remote Control Signal Receiver
NOTE: When the air conditioner is turned on, it will automatically start in the setting last used.
Remote Control
To ensure proper operation, aim the remote control at the signal receiver on the air conditioner.
Make sure nothing is between the air conditioner and the remote control that could block the
The remote control signal has a range of up to 21 feet.
Make sure batteries are fresh and installed
FRUUHFWOVHHWKH&DUHDQG&OHDQLQJVHFWLRQ
Remote Control
1. Press COOL pad.
2. Press LOW or HIGH pads to set desired fan speed.
3. Press the ,1&5($6('(&5($6(pads to set the desired temperature 60F to 85F in 1F increments.
Control Panel
Set the thermostat at a higher number and the indoor air will become warmer.
NOTE: If the air conditioner is off and is then turned on while set to COOL, it w
