When the air conditioner is turned on, it will automatically start in the setting last used.
Turns air conditioner on and off.
On the remote control, use to set the air conditioner to COOL or FAN mode.
On the air conditioner controls, use to set
COOL or FAN mode at HIGH, MED or LOW fan speed. Indicator lights on the air conditioner controls will show the mode and fan speed selected.
TEMP Increase ? /Decrease ? Pads
Use to set temperature when in COOL
Fan Speeds (Remote control only)
Use to set the fan speed at LOW, MED or
ONWhen the air conditioner is off, it can be set to automatically turn on in half an hour to 24 hours at its previous setting.
Each touch will set the time in half hours up to 10 and then in hours up to 24.
To cancel (CL) the On Timer press the
ON pad again.
OFFWhen the air conditioner is on, it can be set to automatically turn off in half an hour to 24 hours. Each touch will set the time in half hours up to 10 and then in hours up to 24.
To cancel (CL) the Off Timer press the
OFF pad again.
To cancel the timer, press the ON or OFF pads until the display time disappears.
Press to set the air conditioner to run for
8 hours before it automatically returns to the previous setting.
When the sleep timer is set, the set temperature will automatically increase
2F after the second hour then 1F each hour over the next two hours.
To cancel the sleep mode, press the MODE pad or the SLEEP pad a second time.
Remote Control Signal Receiver
? To ensure proper operation, aim the remote control at the signal receiver on the air conditioner.
? Make sure nothing is between the air conditioner and the remote control that could block the signal.
? The remote control signal has a range of up to 21 feet.
? Make sure batteries are fresh and installed correctlysee the Care and Cleaning section.
Remote Control become cooler. Set the thermostat at a higher number and the indoor air will become warmer.
1. Press COOL pad.
2. Press LOW, MED or HI pads to set desired fan speed.
1. Press the MODE pad until the COOL indicator light is lit and the LOW, MED or HI indicator light is lit for the desired fan speed.
2. Press the INCREASE ? / DECREASE ? pads to set the desired temperature 60F to 85F in 1F increments.
For Normal CoolingSelect the COOL mode and
HIGH or MED fan with a middle set temperature.
For Maximum CoolingSelect the COOL mode and HIGH fan with a lower set temperature.
For Quieter & Nighttime CoolingSelect the COOL mode and LOW fan with a middle set temperature.
NOTE: If you switch from a COOL setting to OFF or to a fan setting, wait at least 3 minutes before switching back to a COOL setting.
The fan switch is located behind the front grille on the control box. Access through a hole in control box.
When set at CYCLE (down) the fan cycles on and off.
When set at CONT (continuous, up) the fan runs all the time providing a more balanced temperature. The unit is shipped in the CONT setting.
Care and Cleaning
A thermostat is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the set level of comfort. Set the thermostat at a lower number and the indoor air will
3. Press the INCREASE ? / DECREASE ? pads to set the desired temperature 60F to 85F in 1F increments.
NOTE: If the air conditioner is off and is then turned on while set to COOL, it will take approximately 3 minutes for the compressor to start and cooling to begin.
Use the FAN mode to provide air circulation and filtering without cooling. Since fan only settings do not provide cooling, a temperature setting will not be displayed.
Press FAN pad. Press LOW, MED or HI pads to set desired fan speed.
Press the MODE pad until the FAN indicator light is lit and the LOW, MED or HI indicator light is lit for the desired fan speed.
To open or close the vent:
1. Remove the front grille.
2. Remove the vent card screw.
3. Remove vent card, turn it over and replace it by locating rear hole in card over locating pin inside air discharge and reattaching screw at front.
The unit leaves the factory set at the CLOSE position.
(Mesh end toward back)
(Mesh end toward front)
Horizontal louvers on the front grille let you control the air direction up and
The vent control is located behind the front grille on the right side of the air discharge area. When set at
CLOSE, only the air inside the room will be circulated and conditioned. When set at OPEN, some inside air is exhausted outside.
Remove the front grille to adjust the vertical louvers side-to-side to direct the air left or right.
Auxiliary Controls Temperature Limiting
To reach the auxiliary controls remove the front grille. Access them through the small rectangular opening above the control panel.
Temperature limiting can reduce energy costs by limiting the lowest temperature that can be set for cooling. Temperature limiting is controlled by switches 13 of auxiliary controls.
About the controls on the air conditionermodels with touch pads.
Care and Cleaning
TL1 (C) (Temp. Limit 1 Cool)
TL2 (C) (Temp. Limit 2 Cool)
TL3 (C) (Temp. L