Consumer Support
OffThe fan runs all the time, while the compressor cycles on and off.
This switch must be set at Off in order to use the fan settings (on the mode control).
Remote Control
? To ensure proper operation, aim the remote control at the signal receiver on the air conditioner.
? Make sure nothing is between the air conditioner and the remote control that could block the
? The remote control signal has a range of up to 21 feet.
? Make sure batteries are fresh and installed correctlysee the Care and Cleaning section.
Additional controls and important information.
Do Not Operate in Freezing Outdoor Conditions
This cool-only air conditioner was not designed for freezing outdoor conditions. It must not be used in freezing outdoor conditions.
When the air conditioner is turned on, it will automatically start in the setting last used.
Operating Instructions
Power Outage Recovery Feature
In the case of a power outage or interruption, the unit will automatically re-start in the settings last used after the power is restored. The Timer and
Sleep features will reset to the original setting.
You may need to set a new time if desired.
Use the Cool mode with High (3), Med (2) or
Low (1) fan for cooling. Use the Increase ? /
Decrease ? pads to set the desired temperature
between 64F and 86F in 1F increments.
Cooling Descriptions
For Normal CoolingSelect the Cool mode and High (3) or Med (2) fan with a middle set temperature.
A thermostat is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the set level of comfort. Set the thermostat at a lower number and the indoor air will become cooler. Set the thermostat at a higher number and the indoor air will become warmer.
For Quieter & Nighttime CoolingSelect the
Cool mode and Low (1) fan with a middle set temperature.
NOTE: If the air conditioner is off and is then turned on while set to Cool, it will take approximately 3 minutes for the compressor to start and cooling to begin.
NOTE: If you switch from a Cool setting to Off or to a fan setting, wait at least 3 minutes before switching back to a Cool setting.
Installation Instructions
For Maximum CoolingSelect the Cool mode and High (3) fan with a lower set temperature.
Use the Fan at High (3), Med (2) or Low (1) to provide air circulation and filtering without cooling.
Since fan only settings do not provide cooling, a temperature setting will not be displayed.
When set at CLOSE, only the air inside the room will be circulated and conditioned. When set at
OPEN, some inside air is exhausted outside.
To open the vent, push the lever to the right. To close it, push it to the left.
To open the vent, push the lever to the right. To close it, push it to the left.
Troubleshooting Tips
Vent Control (on some models)
The vent control is located on the inside of the air louvers in the lower right corner.
Safety Instructions
Air DirectionUp and Down (on some models)
Consumer Support
Fingertip pressure on the horizontal louvers adjusts the air direction up or down.
Air DirectionSide-to-Side (on some models)
On some models, the side-to-side air direction is adjusted by the louver levers or by grasping and moving the inner vertical louvers.
Features and appearance may vary.
Controls (on models so equipped)
Operating Instructions
Safety Instructions
About the controls on the air conditionermodels with control knob(s).
ON/OFF Switch
Turns air conditioner on and off.
NOTE: If the air conditioner is off and is then turned on while set in a Cool mode, it will take approximately 3 minutes for the compressor to start and cooling to begin.
Installation Instructions
Fan Switch (on some models)
Use to set the fan speed to LO or HI.
Mode/Temp Control
Use to set the air conditioner to the Fan Only or a
Cool mode.
Fan Only Mode
Use Fan Only at HI or LO Fan to provide air circulation and filtering without cooling.
Troubleshooting Tips
Use a Cool setting with HI or LO Fan for cooling.
Turn the knob clockwise, toward the larger blue area, for the indoor area to become cooler. Turn the knob counterclockwise, toward the smaller blue area, for the indoor air to become warmer.
The Mode/Temp control is used to maintain the room temperature. When set in a Cool mode, the compressor will cycle on and off to keep the room at the same level of comfort.
Cooling Descriptions
For Normal CoolingSelect a Cool mode with the
Mode/Temp knob set at the midpoint.
For Maximum CoolingSelect a Cool mode with the Mode/Temp knob set toward the larger blue area.
For Quieter & Nighttime CoolingSelect a Cool mode with the Mode/Temp knob set toward the smaller blue area.
NOTE: If you move the Mode/Temp control knob from a
Cool setting to the Fan On setting, wait at least 3 minutes before switching back to a Cool setting.
Controls (on models so equipped)
Mode Control
Consumer Support
Hi Cool, Med Cool and Low Cool provide cooling with different fan speeds.
Low Fan or Hi Fan provides air circulation and filtering without cooling.
Thermostat Control
The thermostat control is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the same level of comfort. When you turn the knob to a higher number, the indoor air will become cooler. Turn the knob to a lower number and the indoor air will become warmer.
NOTE: If you move the switch from a cool setting to OFF or to a fan setting, wait at least 3 minutes before switching back to a cool setting.
Cooling Descriptions
For Normal CoolingSelect Hi Cool or Med Cool with the thermostat control at midpoint.
For Maximum CoolingSelect Hi Cool with the thermostat control at the highest number available on your knob.
For Quieter & Nighttime CoolingSelect Low Cool with the thermostat control at midpoint.
Additional controls and important information.
Do Not Oper
