GE® 230/208 Volt Room Air Conditioner ASW18DD user guide

9.7 / 9.7 EER.
Temperature will automatically increase 2F.

ONThe fan and compressor cycle on and off. This results in wider variations of room temperature and humidity. Normally used when the room is unoccupied. Note: The fan will continue to run for a short time after the compressor cycles off.

OFFThe fan runs all the time, while the compressor cycles on and off.

Consumer Support

Remote Control

To cancel the sleep mode, press the SLEEP pad a second time.

Note: The sleep timer will be cancelled if the

TIMER, ENERGY SAVER or MODE pad is pressed.

Remote Control Signal Receiver

This switch must be set at OFF in order to use the fan settings (on the mode control).

Remote Control

? To ensure proper operation, aim the remote control at the signal receiver on the air conditioner.

? Make sure nothing is between the air conditioner and the remote control that could block the

? The remote control signal has a range of up to 21 feet.

? Make sure batteries are fresh and installed correctlysee the Care and Cleaning section.

When the air conditioner is turned on, it will automatically start in the setting last used.

Power Outage Recovery Feature

In the case of a power outage or interruption, the unit will automatically re-start in the settings last used after the power is restored. The TIMER and

SLEEP features will reset to the original setting. You may need to set a new time if desired.

Operating Instructions

Use the COOL mode with HIGH (3), MED (2) or

LOW (1) fan for cooling. Use the INCREASE ? /

DECREASE ? pads to set the desired temperature between 64F and 86F in 1F increments.

NOTE: If the air conditioner is off and is then turned on while set to COOL, it will take approximately 3 minutes for the compressor to start and cooling to begin.

Cooling Descriptions

For Normal CoolingSelect the COOL mode and HIGH (3) or MED (2) fan with a middle set temperature.

For Maximum CoolingSelect the COOL mode and HIGH (3) fan with a lower set temperature.

For Quieter & Nighttime CoolingSelect the

COOL mode and LOW (1) fan with a middle set temperature.

Installation Instructions

A thermostat is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the set level of comfort. Set the thermostat at a lower number and the indoor air will become cooler. Set the thermostat at a higher number and the indoor air will become warmer.

NOTE: If you switch from a COOL setting to OFF or to a fan setting, wait at least 3 minutes before switching back to a COOL setting.

Use the FAN at HIGH (3), MED (2) or LOW (1) to provide air circulation and filtering without cooling.

Safety Instructions

Since fan only settings do not provide cooling, a temperature setting will not be displayed.

Vent Control (on some models)

Troubleshooting Tips

The vent control is located on the inside of the air louvers in the lower right corner.

When set at CLOSE, only the air inside the room will be circulated and conditioned. When set at

OPEN, some inside air is exhausted outside.

To open the vent, push the lever to the right.

To close it, push it to the left.

Air DirectionUp and Down (on some models)

Fingertip pressure on the horizontal louvers adjusts the air direction up or down.

Consumer Support

Air DirectionSide-to-Side (on some models)

On some models, the side-to-side air direction is adjusted by the louver levers or by grasping and moving the inner vertical louvers.

Safety Instructions

About the controls on the air conditionermodels with control knobs.

Features and appearance will vary.

Operating Instructions

MODE CONTROLS

Your model will have one of the above type controls.

Installation Instructions

TEMP CONTROLS

Your model will have one of the above type controls.

Troubleshooting Tips

Mode Controls

Temp Controls

HIGH COOL, MED COOL and LOW COOL provide cooling with different fan speeds.

The temp control is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the same level of comfort. When you turn the knob to a higher number, the indoor air will become cooler. Turn the knob to a lower number and the indoor air will become warmer.

LOW FAN or HIGH FAN provides air circulation and filtering without cooling.

NOTE: If you move the switch from a cool setting to OFF or to a fan setting, wait at least 3 minutes before switching back to a cool setting.

Cooling Descriptions

For Normal CoolingSelect HIGH COOL or MED

COOL with the temp control at midpoint.

Consumer Support

For Maximum CoolingSelect HIGH COOL with the temp control at the highest number available on your knob.

For Quieter & Nighttime CoolingSelect LOW COOL with the temp control at midpoint.

Additional controls and important information.

Energy Saver (on some models)

The energy saver switch controls the fan.

ON The fan and compressor cycle on and off together. This results in wider variations of room temperature and humidity. Normally used when the room is unoccupied.

Operating Instructions

ENERGY SAVER

OFF The fan runs all the time, while the compressor cycles on and off.

This switch must be set at OFF in order to use the fan settings (on the mode control).

Vent Control (on some models)

The vent control is located on the inside of the air louvers in the lower right corner.

Installation Instructions

When set at CLOSE, only the air inside the room will be circulated and conditioned. When set at

OPEN, some inside air is exhausted outside.

To open the vent, push the lever to the right.

To close it, push it to the left.

Air DirectionSide-to-Side

AUTO CIRCULAIRE (on some models)

On some models, the side-t