Press to set the air conditioner to run for 8 hours before it automatically shuts off.
For fixed side-to-side air direction, turn ON until the desired air direction is obtained, then turn it OFF.
When the SLEEP pad is pressed, SLEEP scrolls across the display for approximately 15 seconds, then shows the time remaining.
ENERGY SAVER Controls the fan.
One hour after the sleep timer is set, the set temperature will automatically increase 1F.
ONThe fan and compressor cycle on and off.
This results in wider variations of room temperature and humidity. Normally used when the room is unoccupied.
Note: The fan will continue to run for a short time after the compressor cycles off.
OFFThe fan runs all the time, while the compressor cycles on and off.
Consumer Support
Remote Control
To cancel the sleep mode, press the SLEEP pad a second time.
Note: The sleep timer will be cancelled if the
TIMER, ENERGY SAVER or MODE pad is pressed.
Remote Control Signal Receiver
This switch must be set at OFF in order to use the fan settings (on the mode control).
Remote Control
? To ensure proper operation, aim the remote control at the signal receiver on the air conditioner.
? Make sure nothing is between the air conditioner and the remote control that could block the signal.
? The remote control signal has a range of up to 21 feet.
? Make sure batteries are fresh and installed
correctlysee the Care and Cleaning section.
When the air conditioner is turned on, it will automatically start in the setting last used.
Lights beside the touch pads on the air conditioner control panel indicate the selected settings.
A thermostat is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the set level of comfort. Set the thermostat at a lower number and the indoor air will become cooler. Set the thermostat at a higher number and the indoor air will become warmer.
NOTE: If the air conditioner is off and is then turned on while set to COOL, it will take approximately 3 minutes for the compressor to start and cooling to begin.
Cooling Descriptions
For Normal CoolingSelect the COOL mode and HIGH or MED fan with a middle set temperature.
Operating Instructions
Use the COOL mode with HIGH, MED or LOW fan for cooling. Use the INCREASE ? / DECREASE ? pads to set the desired temperature between 64F and 86F in 1F increments.
Safety Instructions
For Maximum CoolingSelect the COOL mode and
HIGH fan with a lower set temperature.
For Quieter & Nighttime CoolingSelect the COOL mode and LOW fan with a middle set temperature.
NOTE: If you switch from a COOL setting to OFF or to a fan setting, wait at least 3 minutes before switching back to a COOL setting.
Installation Instructions
Use the FAN at HIGH, MED, or LOW to provide air circulation and filtering without cooling. Since fan only settings do not provide cooling, a temperature setting will not be displayed.
Vent Control
The vent control is located on the inside of the air louvers in the lower right corner.
Troubleshooting Tips
When set at CLOSE, only the air inside the room will be circulated and conditioned. When set at OPEN, some inside air is exhausted outside.
To open the vent, push the lever to the right.
To close it, push it to the left.
Air Direction Up and Down
Fingertip pressure on the horizontal louvers adjusts the air direction up or down.
Consumer Support
Features and appearance will vary.
Operating Instructions
Safety Instructions
About the controls on the air conditionermodels with control knobs.
MODE CONTROLS
Your model will have one of the above type controls.
Installation Instructions
TEMP CONTROLS
Your model will have one of the above type controls.
Troubleshooting Tips
Mode Controls
Temp Controls
HIGH COOL, MED COOL and LOW COOL provide cooling with different fan speeds.
The temp control is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the same level of comfort. When you turn the knob to a higher number the indoor air will become cooler. Turn the knob to a lower number and the indoor air will become warmer.
LOW FAN or HIGH FAN provides air circulation and filtering without cooling.
NOTE: If you move the switch from a cool setting to OFF or to a fan setting, wait at least 3 minutes before switching back to a cool setting.
Cooling Descriptions
For Normal CoolingSelect HIGH COOL or MED
COOL with the temp control at midpoint.
Consumer Support
For Maximum CoolingSelect HIGH COOL with the temp control at the highest number available on your knob.
For Quieter & Nighttime CoolingSelect LOW COOL with the temp control at midpoint.
Additional controls and important information.
Energy Saver (on some models)
The energy saver switch controls the fan.
OFF The fan runs all the time, while the compressor cycles on and off.
ON The fan and compressor cycle on and off together. This results in wider variations of room temperature and humidity. Normally used when the room is unoccupied.
Safety Instructions
This switch must be set at OFF in order to use the fan settings (on the mode control).
Operating Instructions
Vent Control (on some models)
The vent control is located on the inside of the air louvers in the lower right corner.
When set at CLOSE, only the air inside the room will be circulated and conditioned. When set at OPEN, some inside air is exhausted outside.
Installation Instructions
To open the vent, push the lever to the right.
To close it, push it to the left.
Air Direction Side-to-Side
On some models, the side-to-side air direction is adjusted by the louver levers or by grasping and moving the inner vertical louvers .
CIRCULAIRE (on some models)
For fixed side-to-side air direction, set the
Circulaire switch to ON until the desired air direction is obtained, then move it to OFF.
For continuous side-to-side air circulation, set the
Circulaire switch to ON and leave it there.
Troubleshooting Tips
Air Direction Up and Down (on some models)
