GE® Portable 120 Volt Room Air Conditioner APN08AA user guide

120 Volts.
Or FAN mode.

Troubleshooting Tips

Use to set temperature when in COOL mode or to set a time with the timer feature.

Use to set the fan speed to LOW, MEDIUM or HIGH.

Remote Control Signal Receiver

CIRCULAIRE

Turn on to provide continuous side-to-side air circulation.

For fixed side-to-side air direction, turn on until the desired air direction is obtained, then turn it off.

Consumer Support

ONThe air conditioner can be set to automatically come on in 1/2 (0.5) to 24 hours at its previous setting. The unit must be on while setting TIMER ON.

1. Press the POWER (ON/OFF) pad.

2. Press the TIMER ON pad. The TIMER ON light will blink.

3. Press the pad to set the desired time for the unit to start. (Each time you pads, the set time will advance by 30 minutes between 0 and 10 hours and by one hour between 10 and 24 hours.)

4. Press the TIMER ON pad again to start the timer.

5. Press the POWER (ON/OFF) pad to turn the

Water Full Indicator Light

When the Water Full Indicator Light begins blinking, the unit has reached maximum water collection level.

If water level does not lower in 40 minutes, the unit will power off and it must be manually drained.

1. Unplug the power cord and roll the unit to a drain or outside.

2. Pull out the drain cap from the back bottom edge and allow water to drain from the unit.

3. Replace the drain cap and put the unit back into operation.

NOTE: The unit is designed to automatically

evaporate water collected in normal settings.

However, in very humid settings, the unit may occasionally need to be drained.

The display will always default to show the room temperature.

When the air conditioner is turned on, it will automatically start in the last mode and fan settings

Use the COOL mode for cooling.

Operating Instructions

DRY ModeDehumidification

Use the DRY mode to provide dehumidification only. The fan will run at a fixed speed at this setting, so a fan speed cannot be set. Keep windows and doors closed for the best dehumidifying effects.

The exhaust hose must be attached to the unit when using the DRY mode.

If using the unit in the DRY mode for an extended time:

1. Unplug the power cord.

2. Roll the unit so that its drain nozzle is located over a floor drain and pull out the drain cap from the back bottom edge. A water hose (not included) may also be attached to the nozzle and led to a floor drain. Reconnect the power cord.

3. Press the MODE pad until the DRY indicator light

Use the FAN mode to provide air circulation and filtering without cooling.

To set the FAN mode:

Press the FAN pad until the desired indicator light for HIGH, MEDIUM or LOW fan speed is lit.

Since fan only settings do not provide cooling, a set temperature will not be displayed. After FAN speed has been set, the display will change back to show the room temperature.

In the case of a power outage or interruption, the unit will automatically re-start in the settings last used after the power is restored.

NOTE: If the TIMER was set before the power outage, it will need to be reset after power is restored.

Consumer Support

Power Outage Recovery Feature

Troubleshooting Tips

To set the DRY mode:

Press the MODE pad until the DRY indicator light

In the DRY mode, a set temperature will not be displayed. After DRY mode has been set, the display will change back to show the room temperature.

NOTE: If you switch from a DRY setting to OFF or to a fan setting, wait at least 3 minutes before switching back to a DRY setting.

Care and Cleaning

To set the COOL mode:

1. Press the MODE pad until the COOL indicator light is lit.

2. Press the FAN pad to set HIGH, MEDIUM or LOW fan speed. to set the desired temperature between 64F and 90F in 1F increments.

After settings have been made, the display will change back to show the room temperature.

The temperature control is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the set level of comfort.

Set the temperature control at a lower number and the indoor air will become cooler. Set the temperature control at a higher number and the indoor air will become warmer.

NOTE: If the air conditioner is off and is then turned on while set to COOL, it will take approximately 3 minutes for the compressor to start and cooling to begin.

Cooling Descriptions

For Normal CoolingSelect the COOL mode and

HIGH or MEDIUM fan speed with a middle set temperature.

For Maximum CoolingSelect the COOL mode and HIGH fan speed with a lower set temperature.

For Quieter & Nighttime CoolingSelect the COOL mode and LOW fan speed with a middle set temperature.

NOTE: If you switch from a COOL setting to OFF or to a fan setting, wait at least 3 minutes before switching back to a COOL setting.

Safety Instructions

Turn the air conditioner off and remove the plug from the wall outlet before cleaning.

To clean the case:

Use water and a mild detergent. Do not use bleach or abrasives.

Air Filter

Operating Instructions

Safety Instructions

Care and cleaning of the air conditioner.

The air filter is on the back of the air conditioner.

It should be checked and cleaned at least every

30 days or more often if necessary.

Air filter

NOTE: DO NOT put the filter in an automatic dishwasher.

DO NOT operate the air conditioner without the filter because dirt and lint will clog it and reduce performance.

Care and Cleaning

To remove:

Grasp the tab and gently pull the filter up and out.

Wash it in warm soapy water. Rinse and let the filter dry before replacing it.

Drainage/Routine Maintenance

This air conditioner produces water during normal operation. The unit should be drained if it is not going to be run for an extended period of time.

The unit should also be drained prior to storage at the end of the cooling season.

Troubleshooting Tips

To drain the unit, follow the instructions below:

1. Unplug the power cord and roll the unit to a drain or outside.

2. Pull out the drain cap and allow water to drain from the unit.