GE Profile™ 36" Telescopic Downdraft System JVB67AWW user guide

Removable grease filter.
Of the downdraft cover when it is being

? Keep hands and fingers away from all downdraft parts.

Cooking Tips

The high air movement of this downdraft system can increase the cooking times for some foods. It may take longer to reach high cooking temperatures if the downdraft is turned to high right away. Adjust the fan speed for best cooking results.

The downdraft may not completely capture all the steam from pans on the front burners.

When canning foods in a water-bath canner, a gentle but steady boil must be maintained continuously for the required time.

When canning foods in a pressure canner, the pressure must be maintained continuously for the required time.

Use of the blower at HIGH speed when canning may reduce the temperature enough to stop boiling. While canning, we recommend using the downdraft at

LOW speed and using the front surface unit.

Care and cleaning of the downdraft system.

Grease Filters

To remove: Pull the filters out by grasping them and pulling straight up. be used to remove embedded soil. Rinse, shake and remove moisture before replacing.

Filters may also be cleaned in the dishwasher.

With careful handling, the filter will last for years. If replacement becomes necessary, order the part from your dealer.

To clean: Soak and then agitate in a hot detergent solution. Light brushing may

Installation Instructions

The efficiency of your downdraft depends on a clean filter. Frequency of cleaning depends on the type of cooking you do.

Grease filters should be cleaned at least once a month. Never operate the downdraft without the filters in place.

Operating Instructions

For best results when heating oil for deep frying or when boiling water, use the front surface units or wait until the water is boiling or the oil is at frying temperatures before turning on the downdraft.

Safety Instructions

Painted or Metal Surfaces

Do not use abrasive cloth, steel wool pads or scouring powder because they will mar the

Stainless Steel Surfaces (on some models)

Do not use a steel-wool pad; it will scratch the

Shake bottle well.

Place a small amount of CERAMA

BRYTE Stainless Steel Appliance

Cleaner on a damp cloth or damp paper towel.

Dry and buff with a clean, dry paper towel or soft cloth.

Repeat as necessary.

NOTE: If a mineral oil-based stainless steel appliance cleaner has been used before to clean the appliance, wash the surface with

To order CERAMA BRYTE Stainless Steel

Appliance Cleaner, please call our toll-free

Consumer Support

Clean a small area (approximately

8? x 8?), rubbing with the grain of the stainless steel if applicable. dish soap and water prior to using the

CERAMA BRYTE Stainless Steel Appliance

Cleaner. After washing the surface with dish soap and water, use a generous amount of

CERAMA BRYTE Stainless Steel Appliance

Cleaner to clean the appliance.

Troubleshooting Tips

Clean greasy surfaces frequently, using a mild detergent.

National Parts Center



Stainless Steel Appliance

Cleaner ... ... ... ... ... . . .# PM



Downdraft Vent



Read these instructions completely and carefully.

Open the carton and remove parts package.

Check contents to be sure all pieces are present. (The parts package may be attached to the power cord.)

Save these instructions for local inspectors use.

Remove the shipping materials. Remove the carton and set aside. The carton can be used as a pad when changing or adjusting vent direction.

Observe all governing codes and ordinances.

Note to Installer Be sure to leave these instructions with the Consumer.

Note to Consumer Keep these instructions for future reference.

Note This appliance must be properly

Proper installation is the responsibility of the installer.

Product failure due to improper installation is not covered under the Warranty.



Stabilizing brackets

(all models) (4)

Flat-blade screwdriver

Remote raise/lower assembly (for 36? models only)

Carpenter square

Wire box (2) and screws (4)

Plastic strain relief (2)

Switch cover

Attachment bracket (1)

Ductwork to suit the installation

Wire and white connector (1)

Installation Instructions


Wall coverings, countertops and cabinets should withstand 200F. heat generated by any cooktop.

30? Models

36? Models



IMPORTANT: These vents are recommended for island installations.

Against-the-wall installations are limited due to countertop depth requirements. The vent and cooktop combined depth requires an extra deep flat countertop surface.




The countertop must be at least 26? deep with a flat surface area of 231?2? or more, front to back. (NOTE: JGP932S, JP350SC, JP930SC and JP938SC require 235?8? flat surface area.)

In addition, other clearances to the front edge of the countertop must be considered.