Not all features are on all models.
Rearranging the Shelves
Shelves in the refrigerator and freezer compartments are adjustable.
Refrigerator Compartment
Operating Instructions
Half-Width Shelves
One end of the shelf rests on a molded side-wall support; a bracket on the other end hooks into a track on the rear cabinet wall.
To remove:
Tilt the shelf up at the front.
Lift the support off and out of the track.
Installation Instructions
To replace:
While tilting the shelf up, insert the top hook at the back of the shelf in a slot on the track.
Lower the front of the shelf until the bottom of the shelf locks into place.
Troubleshooting Tips
NOTE: The shelf to the right of the track is designed to hook into the right-hand slot; the shelf to the left is designed to hook into the left-hand slot.
Freezer Compartment
To remove:
Lift up the left side of the shelf and slide it left into the center of the shelf
Rotate the right side of the shelf up and
out of the shelf supports.
Consumer Support
To replace:
Holding the shelf diagonally, insert the left end of the shelf into the center of the shelf supports on the side wall.
Insert the right end of the shelf into the shelf supports on the side wall.
Rest each end of the shelf on the bottom of the shelf supports.
Not all features are on all models.
Fruit and Vegetable Crispers
Excess water that may accumulate in the bottom of the drawers or under the drawers should be wiped dry.
Operating Instructions
Adjustable Humidity Crisper
Slide the control all the way to the
HIGH setting to provide high humidity recommended for most vegetables.
Safety Instructions
About the crispers and pans.
Slide the control all the way to the LOW setting to provide lower humidity levels recommended for most fruits.
Installation Instructions
This pan can be moved to the most useful location for your familys needs.
To remove, slide the pan out to the stop position, lift the pan up and past the stop position, and lift out.
Troubleshooting Tips
Consumer Support
Not all features are on all models.
Crisper Removal
Unload the bottom shelf before attempting to remove the storage drawers.
To Remove:
Lift the drawers up slightly while pulling them past the stop location.
If the door prevents you from taking out the drawers, first try to remove the door bins. If this does not offer enough clearance, the refrigerator will need to be rolled forward until the door opens enough to slide the drawers out. In some cases, when you roll the refrigerator out, you will need to move the refrigerator to the left or right as you roll it out.
To remove the glass cover:
Remove the glass, then the frame. When replacing the glass, push the front edge firmly into the frame.
Push up the glass cover at the rear.
Removing the glass cover
Slide the glass cover backwards until the front edge comes out of the frame.
Rotate the side of the glass cover up.
Remove the glass cover.
To remove the frame:
Lift up the front of the frame using both hands.
Slide the frame forward.
Rotate the side of the frame up.
Removing the frame
Consumer Support
Troubleshooting Tips
Installation Instructions
Operating Instructions
Safety Instructions
About crisper removal.
Remove the frame.
A newly-installed refrigerator may take 1224 hours to begin making ice.
Automatic Icemaker (on some models)
There are 2 types of icemakers:
The icemaker will produce approximately
3 to 31?2 lbs. of ice in a 24-hour period, depending on the freezer compartment temperature, room temperature, number of door openings and other use conditions.
Power Light
Feeler Arm
Power switch model
If the refrigerator is operated before the water connection is made to the icemaker, set the power switch to O (off) or move the feeler arm to the STOP (up) position.
When the refrigerator has been connected to the water supply, set the power switch to the I (on) position or move the feeler arm to the ON (down) position. On power switch models, the green light will come on.
Feeler arm model
Once the icemaker starts to make ice, it may take up to 48 hours to fill the bin, depending on the temperature settings and number of door openings.
When the bin fills to the level of the feeler arm, the icemaker will stop producing ice.
It is normal for several cubes to be joined
If ice is not used frequently, old ice cubes will become cloudy, taste stale, shrink or fuse together.
On power switch models, the green power light will blink if ice cubes get stuck in the icemaker. To correct this, set the power switch to O (off) and remove the cubes.
Set the power switch to I (on) to restart the icemaker. After the icemaker has been turned on again, there will be a delay of about 45 minutes before the icemaker resumes operation.
Installation Instructions
Feeler Arm in
Feeler Arm in (up) position the ON (down)
The icemaker will fill with water when it cools to 15F. A newly-installed refrigerator may take 12 to 24 hours to begin making ice cubes.
