Kenmore Elite 71633 9.2 cu. ft. Top-Load Gas Dryer with SmartDry Ultra – Metallic user guide

An Easy, Breezy Laundry Day Take the hassle out of laundry day with the spacious Kenmore Elite 9.2 cu. ft. top-load gas dryer. Designed to treat your laundry right, this dryer with SmartDry Ultra technology makes it possible to get out of the laundry room and back to life after you toss in a load. Worried about the big event? With Steam Refresh, this gas dryer ensures your clothes will come out ready-to-wear every time. Lots of Room for Large Loads This 9.2 cu. ft. capacity perfect for family-sized laundry, from bedding and towels to jeans and school clothes Handle bulkier items, like rugs and puffy comforters, with ease Fresh and Ready Steam Refresh reduces wrinkles and odors from your laundry Smarter Drying Power SmartDry Ultra technology fine-tunes temperatures while also measuring moisture levels and adjusting cycle time and heat Quad baffles use an innovative shape to keep clothes tumbling and open for a better and more efficient dry A dual heating element fine-tunes heat levels to prevent over drying
(35 mm) (370 mm)

Bottom view:

NOTE: Most installations require a minimum of 6" (152 mm) clearance behind dryer for exhaust vent with elbow. See

Venting Requirements.

Spacing for recessed area or closet installation

The dimensions shown are for the minimum spacing allowed.

?? Additional spacing should be considered for ease of installation and servicing.

?? Additional clearances might be required for wall, door, and floor moldings.

?? Additional spacing of 1" (25 mm) on all sides of the dryer is recommended to reduce noise transfer.

?? For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilitation openings are acceptable.

?? Companion appliance spacing should also be considered.

Electrical Connection

To properly install your dryer, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.

24" 2//24"

155 cm 22))

(25 mm/25 mm)

(25 mm/0 mm)

Recommended/Minimum spacing

Mobile home Additional installation requirements:

This dryer is suitable for mobile home installations. The installation

must conform to the Manufactured Home Construction and Safety

Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile home construction and Safety, Title 24, HUD Part 280), or Standard CAN/CSA-Z240 MH.

Mobile home installations require:

All dryers:

Require metal exhaust system hardware, available for purchase from your dealer. For further information, see Assistance or Service section in your Use and Care Guide.

Special provisions must be made in mobile homes to introduce outside air into dryer. Openings (such as a nearby window) should be at least twice as large as dryer exhaust opening.

For gas dryers mobile home installations:

Do not use an extension cord.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

Mobile Home Installation Hold-down Kit Part Number

W10432680 is available to order. For further information, see Assistance or Service section in your Use and Care Guide.

This dryer is manufactured ready to install with a 3-wire electrical supply connection. The neutral ground conductor is permanently connected to the neutral conductor (white wire) within the dryer. If the dryer is installed with a 4-wire electrical supply connection, the neutral ground conductor must be removed from the external ground connector (green screw) and secured under the neutral terminal (center or white wire) of the terminal block. When the neutral ground conductor is secured under the neutral terminal (center or white wire) of the terminal block, the dryer cabinet is isolated from the neutral conductor.

If local codes do not permit the connection of a neutral ground wire to the neutral wire, see Optional 3-wire connection section.

A 4-wire power supply connection must be used when the appliance is installed in a location where grounding through the neutral conductor is prohibited. Grounding through the neutral is prohibited for (1) new branch-circuit installations,

(2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductors.

If using a power supply cord:

Use a UL-listed power supply cord kit marked for use with clothes dryers. The kit should contain:

A UL-listed 30-amp power supply cord, rated 120-/240-volt minimum, and have a temperature rating of 140F (60C) minimum. The cord should be type SRD or SRDT and be at least

4 ft. (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned ends.

A UL-listed strain relief.

If your outlet looks like this:

ELECTRICAL REQUIREMENTS

It is your responsibility:

To contact a qualified electrical installer.

To be sure that the electrical connection is adequate and in conformance with the National Electrical Code, ANSI/

NFPA 70 latest edition and all local codes and ordinances. receptacle

If your outlet looks like this:

The National Electrical Code requires a 4-wire power supply connection for homes built after 1996, dryer circuits involved in remodeling after 1996, and all mobile home installations.

A copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02269.

To supply the required 3- or 4-wire, single-phase, 120-/

240-volt, 60 Hz, AC-only electrical supply (or 3- or 4-wire,

120-/208-volt electrical supply, if specified on the serial/rating plate) on a separate 30-amp circuit, f