Lenoxx Electronics CD-163 CD Player user guide

IB-CD163(TA)-FREDS-E-042602

ATTACHING THE SPEAKERS of the set.

2. Align the rails of the speaker box with the main set as shown in FIG.1.

3. When speaker align with the rails, push the speaker into the rails as shown in FIG. 2.

4. Repeat above steps 1 to 3 for the left right plug into Speaker Jack R, also plug the left plug into Speaker Jack L (as shown in FIG. 3). Wrap the remaining wire behind each speaker box.

NOTE: This set can be used with speaker boxes attached to the cabinet or separated, just make sure both speaker plugs are plugged into the jacks.

To remove the speakers, press the lock tab and push the speakers out of the rails.

IB-CD163(TA)-FREDS-E-042602

REMOTE CONTROL

You can control the CD PLAYER with the provided REMOTE CONTROL (including the functions of POWER ON/OFF, MUTE, VOLUME control, CD REPEAT and PLAY features).

NOTE: When you use the REMOTE CONTROL to operate the CD PLAYER, make sure the POWER switch on the main set is turned on, otherwise, the REMOTE CONTROL will have no functions to the set.

POWER ON/OFF

REPEAT - ONE & ALL SONGS

VOLUME UP/DOWN

SKIP/SEARCH BACKWARD

SKIP/SEARCH FORWARD

PLAY/PAUSE

NOTE: When you press the POWER

ON/OFF switch to shut the set off, the STANDBY indicator on the main set will turn on.

A A A

A A A

Slide the battery cover to remove. Insert two size AAA batteries correctly so that the + and - polarities match the polarity diagrams inside the battery compartment.

About half a year of normal operation can be expected when using the alkaline batteries. when the batteries are exhausted, the remote control will no longer operate the system. Replace both batteries with new ones.

When the remote control is not to be used for a long time (2 months or more), remove the batteries to avoid possible damage that may be caused by battery leakage.

Avoid keeping the remote control in extremely hot or humid locations.

The remote controls operating distance is about 0.2m (8 inches) to 6m

(20 feet ) away from the remote sensor.

IB-CD163(TA)-FREDS-E-042602

PLAYING A CD

Connect the supplied AC power cord or batteries (see page 4).

Press the POWER switch, the VFD display will turn on and the

STANDBY lamp will go off.

S TA N D B Y

Set the FUNCTION switch to CD position, two dashes -- will show on the VFD display.

Open the CD DOOR by pressing the right corner marked OPEN/CLOSE and place the CD in the CD compartment.

The label side of the CD should face

Close the CD DOOR by pushing it down. The display will show the total number of tracks (songs) on that

Press the CD PLAY button. The player will play all the songs (tracks) once in order.

To change the sound effect, adjust the BASS and TREBLE knobs to your taste.

TIP:

WILL SHOW IN THE DISPLAY IF THERE IS NO DISC IN THE CD

COMPARTMENT OR IF THE DISC IS UPSIDE DOWN.

IB-CD163(TA)-FREDS-E-042602

USE THESE BUTTONS FOR

ADDITIONAL OPERATIONS

VOLUME CONTROL

When CD play is paused, will flash and no music will play.

FUNCTION SWITCH

To resume play, press the PAUSE button again, will stop flashing and music will play.

If you bump the set or the table it is sitting on, during

CD play, the music will stop or skip for a few seconds.

This is normal for this type of player.

This set has an electronic volume control, you may raise or lower the volume by pressing control (

or

Press or Adjust

Adjust the volume

VOLUME control

Stop playback

PLAY/PAUSE

will flash during pause.

Press again to resume play after pause.

Pause playback

Go to the next track

Go back to the previous

Locate a point in a song

Press and hold down while playing until you find the

Remove the CD

Press the right corner of the

CD DOOR marked OPEN/

CLOSE (press STOP first).

Turn off the power

Press the POWER switch, the display will go off and the

STANDBY lamp will turn on.

IB-CD163(TA)-FREDS-E-042602

REPEAT PLAY

PLAYING CD SONGS