Description
MS9524x or
VoyagerPDF Series Scanner
MetroSelect Single-Line Configuration Guide*
MS9524/44 VoyagerPDF Series Installation and Users Guide*
OPTIONAL ACCESSORIES
Description
AC to DC Power Transformer- Regulated 5.2VDC @ 650 mA output.
120V United States
220V-240V Continental European
220V-240V United Kingdom
220V-240V Australia
220V-240V China
53-53000x-3
RS232 PowerLink Cable with Built in Power Jack
2.7 m (9 ft.) coiled cord, long strain relief, black
54-54000x-3
RS232 PowerLink Cable with Built in Power Jack
2.1 m (7 ft.) straight cord, short strain relief, black
53-53002x-3
Keyboard Wedge PowerLink Cable with Adapter Cable
2.7 m (9 ft.) coiled cord, long strain relief, black
53-53020x-3
Stand-Alone Keyboard Wedge PowerLink Cable
2.7 m (9 ft.) coiled cord, long strain relief, black
Other items may be ordered for the specific protocol being used. To order additional items, contact the dealer, distributor or call Metrologics Customer Service Department at
1-800-ID-METRO or 1-800-436-3876.
SCANNER AND ACCESSORIES
OPTIONAL ACCESSORIES
53-53213x-N-3
Description
USB Full Speed Cable, Locking Plus-Power Type A
2.7 m (9 ft.) coiled cord, long strain relief
USB Full Speed Cable, Locking Plus-Power Type A
4.5 m (15 ft.) coiled cord, long strain relief, black
53-53214x-N-3
This cable is for use with full speed USB (-40) units.
Do not use this cable with low speed USB (-38) units.
53-53235x-N-3
USB Low Speed Communication Cable,
Type A (Non-Locking) Connector
2.7 m (9 ft.) coiled cord, long strain relief, black
Metrologic Voltage Converter Cable, 12VDC to +5.2VDC for IBM and OCIA applications
Contact a Metrologic customer service representative for additional information on the MVC converter cable series and the host connections available.
Free-Standing Stand with Accessories
Hard Mount Accessory Kit (used with kit #46-46128)
46-46433 OR
Wall Mount Hanger Accessory Kit
Other items may be ordered for the specific protocol being used. To order additional items, contact the dealer, distributor or call Metrologics Customer Service Department at
1-800-ID-METRO or 1-800-436-3876.
INSTALLING THE SCANNER TO THE HOST SYSTEM
RS232, Laser Emulation, and Light Pen
(MS9524-14/00/41 or MS9544-14/00/41)
Turn off the host system.
Connect the 10-pin RJ45 male connector into the jack on the
VoyagerPDF. You will hear a click when the connection is made.
Connect the L-shaped plug of the power supply into the power jack on the PowerLink cable.
Make sure the AC input requirements of the power supply match the AC outlet. Connect the power supply into an AC outlet.
The outlet should be near the equipment and easily accessible.
Connect the PowerLink cable to the proper port on the host system.
Turn on the host system.
Plugging the scanner into a port on the host system does not guarantee that scanned information will be communicated properly to the host system. Please refer to the MetroSelect Single-Line Configuration Guide or MetroSet2s help files for instructions on changing the scanners factory default configuration. The scanner and host system must use the same communication protocols.
All MS9524-00/MS9544-00 scanners leave the factory with the Laser
Emulation Mode enabled. If you recall defaults while re-configuring the scanner the Laser Emulation Mode will no longer be enabled. Refer to the MS9520/9540-00 Laser Emulation Mode section of the MetroSelect
Single-Line Configuration Guide for information on enabling the Laser
Emulation Mode.
To maintain compliance with applicable standards, all circuits connected to the scanner must meet the requirements for SELV (Safety Extra Low Voltage) according to EN/IEC 60950-1.
To maintain compliance with standard CSA-C22.2 No. 60950-1/UL 60950-1 and norm EN/IEC
60950-1, the power source should meet applicable performance requirements for a limited power source.
INSTALLING THE SCANNER TO THE HOST SYSTEM
IBM 46xx and OCIA (MS9524-11/9 and MS9544-11/9)
Turn off the host system.
Plug the male 10-pin RJ45 end of the MVC cable into the 10-pin socket on the scanner. You will hear a click when the connection is
Connect the other end of the MVC cable to the host device.
Turn on the host system.
Plugging the scanner into a port on the host system does not guarantee that scanned information will be communicated properly to the host system. Please refer to the MetroSelect Single-Line Configuration Guide or MetroSet2s help files for instructions on changing the scanners factory default configuration. The scanner and host system must use the same communication protocols.
To maintain compliance with applicable standards, all circuits connected to the scanner must meet the requirements for SELV (Safety Extra Low Voltage) according to EN/IEC 60950-1.
To maintain compliance with standard CSA-C22.2 No. 60950-1/UL 60950-1 and norm EN/IEC
60950-1, the power
